Jump to content

Citizen Eco Drive B612 not working

Rishah

By Rishah
in Watch Repairs Help & Advice

 Share

Recommended Posts

Rishah Watch Enthusiast

Rishah

Posted
Posted

I bought a citizen Eco Drive watch nighthawk fb3002 53p as a project watch. It's a beautiful watch but not working properly . The watch's chronological functions are working but the hour/minute/second hand are not working . It's a very strange problem, but that also means that the battery is fine. Has anyone else faced such an issue , any help is welcome. Worst case , where can I find the replacement movement ? 

Thanks in advance 

 

IMG_20210228_204658.jpg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hello Rishah and welcome to the forum.  If the chrono functions are ok it could be the time side coil or a jam in the gear train.  Could you open the watch and post some pictures of the movement. That way members will be able to identify the movement and point you in the right direction      Thanks

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  quite pricey.   If toy have a line release or demagnetiser you could remove the capacitor and try inducing a magnetic field which makes the hands move rapidly it might just be a case of a jammed or sticky gear train  do it in short bursts not prolonged.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • aac58
      Rare Seiko 5actus Watch??!! With a lot🤪🤔😲

      By aac58 · Posted

      This is not rare at all, the dial code and case code don't usually match.
    • Kkramme
      Coil for old Seiko Credor -- 4002920

      By Kkramme · Posted

      Good question!! Anyone know of a substitute movement??!! 🤔🙏
    • Kkramme
      Rare Seiko 5actus Watch??!! With a lot🤪🤔😲

      By Kkramme · Posted

      Interesting issue that I just noticed: this Seiko 5actus Watch from 1977 has a calibre listing on the dial of 7019-8030R but on the case back it says 7019-8010!! Like a mis-printed coin, is this watch therefore worth a lot of money for its rarity?? 🤪😲🤔🤪
    • Mercurial
      Smit

      By Mercurial · Posted

      I wish that was the case. The Aegler movements used in the early days by Wilsdorf & Davis (for brands like Rolex and Rolco) came in several sizes and without designated calibre numbers that survive.  They become a bit easier to identify during the 1920s. Below is an Aegler-Rebberg, 25.74mm in diameter. It’s from a woman’s Rolex wristwatch. Stamped Rebberg and 500 on the dial plate (but it isn’t a Rebberg 500, it’s the wrong size).  I’d be interested if anyone can identify the movement.  It is based off the Aegler Nr.1, circa 1903, but they based many many calibres of different sizes on it. The closest I have to a positive ID is the  ‘Rolex Nr.50’ circa 1917, but no dial side images or movement sizes are available in the references. There are identical looking movements in many sizes.  The 25.74mm of this movement is a particularly strange size for the era, it equates to 11.41 lignes.      Best Regards, Mark
    • GuyMontag
      FHF70 balance jewels settings

      By GuyMontag · Posted

      It looks like this movement comes with a number of different shock settings. Emmywatch shows that it comes in versions with no shock settings, 'Incabloc', 'shock resist', and 'Supershock'. Perhaps the different settings position the impulse jewel/roller table in a non-ideal position relative to the pallet fork/guard pin. Are you able to check under high magnification if the pallet fork and roller table are able to operate without any interference? Just for fun I took a look and I have one FHF 70 in my collection, a West End Secundus with a non-shock protected FHF70. I had a note with the watch that said, "Movement is stamped 'FHF 70', but the FHF70 looks to have sub-seconds instead of center seconds movement (??)" but that a google search turned up both types for this movement. EDIT: I just took a look in my parts drawer and I have a few of these movements, both in center seconds and sweep seconds, but they all are non-shock protected.  
×
×
  • Create New...