Jump to content

Just Finished This One For My Wife!

DJW

By DJW
in Your Watch Collection

 Share

Recommended Posts

DJW Super WRT Addict

DJW

Posted
Posted

First off, let me say I've thoroughly enjoyed the YouTube videos from the "Watch Repair Channel" and more specific, I've enjoyed listening to you, Mark. I've been tinkering with watches now for about 7 years and am self taught. I really wish I could have gone to school to learn the trade, but it was not in the cards!

 

This is one of my latest creations. I hand painted the dial myself and overhauled the Hamilton 917 movement. It is fitted in a 44mm stainless steel case with a matching Leather strap. My wife loves it!

 

post-90-0-66901700-1392213941_thumb.jpgpost-90-0-19354400-1392213954_thumb.jpgpost-90-0-61467800-1392213964_thumb.jpg

  • Like 1
Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

Very nice - my son just gave it a thumbs up ;) (he's an art student).

 

Out of interest - do you finish the dial with anything after painting for protection?

Thank you! and tell your son thanks as well!

 

as far as protection, that's something I'm dealing with right now. I put about 10 coats of varnish on the dial, but varnish remains soft. So, whenever I have to disassemble the watch I have to try and not touch the dial as it will leave a mark, or scratch. This is particularly difficult when removing the hands.  The technique I use is to use a Presto type hand remover and just place the tool directly under the hands and pull up, not ever touching the dial.

 

I'm looking at a clear enamel paint that dries hard to replace the varnish that I use now.

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

How about a clear acrylic lacquer. I would think that would dry hard as nails.

 

I have tried painting dials in the past with pretty bad results, but it is something that really interests me.

 

It's funny you mention that...I just ordered a number of different clears to test and that is one of them. 

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

I'm amazed at your artistic talent,  the Hamilton's are very nice as well.

 

RogerC

Thanks Roger! I'm trying to make a go at it as a business too! But, it's been slow going ;-(

If you have any ideas that I should try, don't hesitate to throw them my way!

 

Don

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

I'm trying to make a go at it as a business too!

 

I know somebody who did something similar with the old Smiths 1215 movement and they have been very successful.

 

They were retailing at around £4k a pop and numbered as exclusive pieces. So you could be on to something if you get the marketing and promotion right.

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

I know somebody who did something similar with the old Smiths 1215 movement and they have been very successful.

 

They were retailing at around £4k a pop and numbered as exclusive pieces. So you could be on to something if you get the marketing and promotion right.

Let's hope so! I've taken this year off work to give it a go! I have about 6 months left to prove to myself that I can do this...

Don

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

Just curios,  where do you get the Hamilton watches from,  they appear brand new.  If it's a trade secret just ignore my curiosity.

 

RogerC

Hi Roger,

Early on I would bid on them on the "Giant Auction site". Typically, I was winning them at around $80-$100us. But lately, I've been trading repair work for movements that need some sort of repair, usually a broken staff. Believe me, I do get some real dogs as well.

 

Amazing artistry and the gem of it is that you have a piece that no one in the whole world has, unique to the person who owns it. It's got to be a winning business just on that fact alone. Nice to meet you DJ.

Hey, Thank you!  

Link to comment
Share on other sites
autowind Distinguished Member

autowind

Posted
Posted

How about gold leaf?  I was just thinking about covering the whole dial in it,  there would be the hour markers to think about,  but there are not many watches with a gold dial.

 

Come to think of it,  Rolex could fit solid gold dials for the money they charge,  but I don't think they do.

 

RogerC

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

Out of interest, where do you get the cases from? I often see pocket watch movements for sale with no case - particularly hunters - and think it would be fun to recase them. My Hamilton Khaki movement is a mechanical ETA 6497 and it looks fine in a wrist casing.

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

How about gold leaf?  I was just thinking about covering the whole dial in it,  there would be the hour markers to think about,  but there are not many watches with a gold dial.

 

Come to think of it,  Rolex could fit solid gold dials for the money they charge,  but I don't think they do.

 

RogerC

I've never thought of that! I could apply leaf to certain areas of the dial such as the outer chapter ring...it has some interesting possabilities...

 

Out of interest, where do you get the cases from? I often see pocket watch movements for sale with no case - particularly hunters - and think it would be fun to recase them. My Hamilton Khaki movement is a mechanical ETA 6497 and it looks fine in a wrist casing.

Most of the cases are from China. Sime are sourced from the US, but are actually Swiss Made. I really like the large size wristwatches with these vintage movements. 

 

Could be something similar to this: http://www.ebay.co.uk/itm/Parnis-44mm-case-fit-6497-6498-movement-/271183993444?pt=LH_DefaultDomain_0&hash=item3f23d35a64

 

Very nice dial painting by the way. I wonder how much you will retail these at? I probably couldn't afford one anyway.

These are simular to the cases I use. Even among asian produced cases, there is a wide range in quality on the case finishes. The case in the listing that you linked was produced for the counterfeit market. If you notice on the side of the watch case there is limited edition engraving...117/1000. There are thousands and thousands of these flooding the market. BTW, this case was produced to make counterfiet IWC F.A. Jones Models. Thse can be had for around $30us from suppliers in China.

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

That's cool - very impressive.

 

Just a thought: have you ever considered doing the painting slightly smaller, inside an inner chapter ring, and with a painted egde, with conventional numerals or batons in the outer chapter? That would give the effect of an old-fashioned miniature painting as part of a watch face. Might be cool as well...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Accutron 218 transistors

      By rjenkinsgb · Posted

      Many would disagree: https://www.rohm.com/products/faq-search/faqId/234 https://uk.farnell.com/c/semiconductors-discretes/transistors/bipolar-transistors/pre-biased-digital-bipolar-transistors https://uk.rs-online.com/web/p/bipolar-transistors/8232832P?gb=s https://uk.rs-online.com/web/p/bipolar-transistors/0580240?gb=s (RS don't have a specific category, but over 1000 "digital transistor" items).  
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Thanks, ManSkirtBrew.  I started looking for a setup like yours and ran across this.  It was about half the price of the JKA Feintaster (depending on what auction you were in), and it's a Bergeon.  I bought it because I thought the price was fair (eBay - Buy it now), and I'm a sucker for vintage tools. It also has a table, so it should be easy to use for measuring jewels. I wonder if the the contact points can be changed out. Bergeon seems to manufacture new tables and accessories for the contemporary dial version. What do you guys think of it? I'm sorry this post seems to have taken a detour. I'm new here so let me know if I should start a new topic.
    • nevenbekriev
      Winding pinion making

      By nevenbekriev · Posted

      This is a flying cutter, usual one. The cutter itself is shown in the pictures in the first message, it is made of broken tungsten carbide drill bit. I asure that all the angles of the cutter are as they should be. I have video - little older one - that I made when onse making the same kind of winding pinion for a Poljot 2200, which is even smaller than this one. It is not easy to see in the video, but the tool rest moves about 1mm towards the object in Y direction and then returns back untill cutter is rotating. Then the spindle is rotated one tooth ahead and everything repeated untill all teeth are cut.
    • Trav2004
      Help Identifying movement

      By Trav2004 · Posted

      After a bit further research could it possibly be an AS 970?
    • Bonefixer
      FHF70 balance jewels settings

      By Bonefixer · Posted

      Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
×
×
  • Create New...