Jump to content

Help please Swiss Emperor 17 Jewels information needed


Recommended Posts

That is a beautiful watch.

I am not sure if its movement is by Pesuex, ETA or AS manual wind, supriority of any over other two is debatable, I personally am fond of peseux.

As new as this is, selling is a shame and I am hesitant to appraisae,  should fetch two to three folds the price of a used one in good shape, One with Stainless steel back , anywhere between 275 to 350  USD  wouldn't surprise me, smell of the bracelete or sign of having been worn, ha ha if its been worn knock up to 50 buck off the price. Please note I am violating WRT policies cuz your watch is so beautiful.

Wind three to four turns of the crown every two months, if it runs inaccurate or starts to at anytime, have it cleaned and lubed by a reputable serviceman. Continue the two months ritual. 

 

Good luck.

  • Like 1
Link to comment
Share on other sites

Is it gold? If gold it will depend on the weight and what karat gold. The movement would be taken out and the glass ,to find its weight.

if not gold here in England about £150 if you are lucky, as its not a high class movement like an Omega or Rolex just to name two. I can see that the bracelet isn't gold but plate. With a stainless steel back I would say it isn't gold. 

  • Like 1
Link to comment
Share on other sites

I think it's a very lovely watch, but not worth that much. After a little search I've found that particular model, with with the stainless steel back, gold plated case, arabics at 12, 6 and 9 with the date at 3, and the seconds subdial, sold at auctions for anywhere from £35.00 to £55.00.

If there's sentimental value, by all means have it serviced and wear it proudly. I would get rid of that bracelet though, and put it on a nice leather strap.

  • Thanks 1
Link to comment
Share on other sites

1 hour ago, eccentric59 said:

I think it's a very lovely watch, but not worth that much. After a little search I've found that particular model, with with the stainless steel back, gold plated case, arabics at 12, 6 and 9 with the date at 3, and the seconds subdial, sold at auctions for anywhere from £35.00 to £55.00.

If there's sentimental value, by all means have it serviced and wear it proudly. I would get rid of that bracelet though, and put it on a nice leather strap.

It will look like them £35 ones before long if he wears it.

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • After a bit further research could it possibly be an AS 970?
    • Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
    • Oh and this almost perfect third wheel pivot and slightly set mainspring  Ah ok yes i see what you mean, good idea. I'll try that if i fluff this one up. The image isn't great quality but i like the idea though.
    • Why cut the paper, cut a square around the image and grind to it. 
    • I did try that last time Rich , i traced the image from the Bestfit book which is the actual size. But its more difficut to cut the shape from paper than it is to grind the steel to shape. This way is pretty easy and the final shaping is done when fitting the part. There are a couple of things i will do differently next time, clamping the 2 pieces together with a drill press will help to hold while scribing the shape in. This was a bit tricky having only one hole, if using the pins and cork the drill size needs to match the pin diameter so there is no movement at all from the template. This movement hasn't finished frying me yet, damaged thread in the plate crown wheel hole and two rubbed in cracked jewels, thats gonna be much more fun.
×
×
  • Create New...