Jump to content

Can someone with the Horotec triple hand press please help me out?

Halvis

By Halvis
in Tools & Equipment

 Share

Recommended Posts

Halvis Watch Enthusiast

Halvis

Posted
Posted

I consider buying the triple hand press from Horotec and a Bergeon 5409 (movement holder for fitting hands)

Can someone with the Horotec press please measure if the pillars will conflict with the movement holder when using the first and third plunger?

The diameter of the holder is 35 mm, and the stakes on the press needs to hit it in the middle because of the support pin.

 

This will help me out tremendously, as I would hate to buy them and find that they are not compatible.

 

h44238_pic1a_cmyk1.jpg

5409.1__29559.1477013043.jpg?c=2&imbypas

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Looking for advice on removing the glass and bezel

      By Jon · Posted

      Yes, Mine has a support for the blade that can be safely hit like this one https://www.amazon.co.uk/Rolson-62841-Tradesman-Knife/dp/B0044D9MC6/ref=sr_1_37?crid=3HWJF1HL4J8D7&dib=eyJ2IjoiMSJ9.X58oai8WcFho_-XqfR-lLQbU8lQKhf1vtFKAWbXR4EAhqVWR_eMy5h1DhaCULvkpA6XT0GaNFLHt_kJ0kPrhXFo0nYd8yJ4JgruoXDG9XjViAQOyAiBUkOhC9W9qQfGr0SMKpxIUrGOBkTjtTPTuM9IOTnb-dEAzbcZVvniVcEuMFGK9SITyDO6ryUU8ERkHt8f2Vy9Ks0QFO06KSJz65C2p7S3o2lOaUoO9kw61KyNtaaYYwdZzyuM2uRywODaigUn0u8RHMPR0dOa3WSrq8vE1iV5Et_561SFfvkhSGTQ.9QrdWVoCJpLVkrflNS1sxaY56ys4iiJspEFpUgLIRdg&dib_tag=se&keywords=stanley+knife&qid=1716289527&sprefix=stanley+knife%2Caps%2C77&sr=8-37 I use a brass hammer. You could use a very light pin hammer. A watchmaker's hammer would be a bit too light to use. I'm not sure of the weight, but looking at Cousins, it looks like a 60 or 84g brass hammer. I would go with the 84g one. A lot of the process is about feel, so you don't damage the case or bezel. Don't twist the tool! You may think it would make it easier and quicker, but that's when the damage starts to happen and be especially careful around the lugs. Once you have done a couple, you'll get a feel of it. Some bezels feel like they're not coming off and you start to doubt what you are doing. The trick is to be deliberate in your actions, rather than tentative. If you perform this task with the total belief that the bezel is coming off, that is exactly what will happen. First, be totally sure that the bezel comes off in the way you expect.   Rub the blade against a piece of 400 grit wet and dry until blunt
    • Neverenoughwatches
      Favourite timepiece.

      By Neverenoughwatches · Posted

      I do like the idea of clocks , you get so much more for your money than you do when buying a watch.
    • oldhippy
      Favourite timepiece.

      By oldhippy · Posted

      No but I have taken it out of its case to make sure all is well. 
    • Neverenoughwatches
      Breguet hairspring frequency

      By Neverenoughwatches · Posted

      I read recently that there are almost 600 different patterns of overcoil.
    • oldhippy
      Hello

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.  Gabriel clocks are my thing.
×
×
  • Create New...