Jump to content

Are Seiko samurai and turtle Bezels interchangeable?

Ruairidh

By Ruairidh
in Watch Repairs Help & Advice

 Share

Recommended Posts

jdm Distinguished Member

jdm

Posted
Posted

There is no secret places for parts, all one can find is revealed by Internet search. Now, if you are looking for new parts for the original 7S26 watch, I don't think you can find any. And for the new 4R36 you could try having Cousins or an official Seiko dealer make an order. Anyway it would be very expensive compared to the cost of the complete watch.

  • Thanks 1
saswatch88 WRT Addict

saswatch88

Posted
Posted (edited)
2 hours ago, Ruairidh said:

Just wondering and does anyone know anywhere good to by parts for a Samurai?

The bezels between turtles and samurai are interchangeable!  Not many people know this, assuming you mean a prospex turtle. SKX models can easily be found on eBay. I purchased a brand new oem Seiko bezel and insert for my skx009 it was $69. Parts for the 4R36 are also available a bezel & insert for the turtle is about $139.

there also many sights who sell aftermarket bezels/inserts for the samurai. Just do a search on the net but here is one:

https://www.dlwwatches.com/collections/ceramic-bezel-inserts/samurai

there are no secret places for parts because they are everywhere. I just wish it was the same for deep blue watches.

Edited by saswatch88
  • Thanks 1
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Nucejoe
      Bizarre state of the balance! Miyota 8200

      By Nucejoe · Posted

      No need for special tools. Loosen stud screw and just push hairpsring stud out of the hole.  Regulator arm is spring circled around the setting housing, insert cutting edge of a safety blade under it,  opposit ( 180 degrees) to regu arm itself, and pry  half of the circle up, you then see how it all is made at put together. Remove the mobile stud carrier as well,  reinstal in proper order, first goes on the stud carrier, second put the regulator arm on top and press it home. Exactly as nev explained above. Trueing inner coils is done when balance complete is seperated from the cock.   The part thats bent over itself. 1-Unbend hairspring as much as you can when balance is seperated, just grab the hairspring stud in tweezers , grab hairpsring with another tweezers streighten with  strokes as you  move the second tweezers  away from the stud. 2-Move stud carrier and regulator arm as wide/ apart as they go , to provide max space which comes useful in next step. 3- Fit hairspring stud, into stud carrier hole. 4- Put balance and cock ( when attached together) back on mainplate.  5- You have enough space to grab hairspring in  tweezers to shape as you move your tweezers  away from stud.         
    • RickTock
      Looking to try servicing an old movement

      By RickTock · Posted

      Probably more than you need to know in these two vids, but sharing because I found them quite interesting. 🙂  
    • SamLiddle
      Bizarre state of the balance! Miyota 8200

      By SamLiddle · Posted

      And then the problem of the stud holder and regulator which are on the wrong sides of each other:   I am baffled as to how this will have happened?  They can't re rotated into place, the regulator pins stop the spring stud from moving past. I don't think I can remove the regulator and/or spring stud without a staking set? 
    • nevenbekriev
      Help! Mainspring releasing power!

      By nevenbekriev · Posted

      Just to inform that this is not a shock protection, just end stone fixed in place by the spring.
    • AndyGSi
      Could anybody work on a screw this small?

      By AndyGSi · Posted

      I had the privilege to be put on secondment to RR Ansty just outside Coventry to help design and build a power station at the old Fort Dunlop site in Birmingham. The sound of those Trent engines when they fire up is something to behold.
×
×
  • Create New...