Jump to content

Starting Out

AlexC
 Share

Recommended Posts

AlexC New Member

AlexC

Posted
Posted

So, just signed up and having read some of the post i fancy buying a broken watch off e bay and seeing if i can get it going again.

 

Any recomendations on what i should buy ? Ideally should be a simple a movement as i can get, plentiful and cheap to buy, really easy to work on !!

 

Cheers

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I think you should buy an old movement that actually works, strip it down, re-assemble and see if it still works before tackling something that is broken. Once you can do that buy a watch that doesn't work and try and fix it.

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted (edited)

I second Geo's advise. I'll even say, if your funds allow, buy a new watch and do Geo's recommendation with it.

 

Make sure it is a popular and regular to big size movement (11 1/2 ligne or bigger) they are better to start with. Good candidates are: ETA 6497, 6498, 2801 family (2801, 2804, 2824, 2836) and similar, Seiko 7S26 family and more modern equivalents, Citizen 8200 and similar. In fact, something with service data available so you can follow the diagram of where every thing goes, oil schedule, etc. (you might be cleaning and oiling later down the road). Be prepared to mess up your first hairspring (so parts should be available to replace the broken one), some pivots, etc. If you don't good, if you do, no problem as long as the part can be replaced and the error learned.

 

You can also take an online class and most important, whatever you do, watch lots of related movies (youtube) specially Mark's movies (link on this site's top bar) which are perfect and to the point. Most recommended is his servicing an ETA 2824-2 in two parts: good for beginners and experts alike.

 

Also, buy good tools mostly good tweezers and good screwdrivers, that's where your money should go first. Otherwise you will be frustrated and very disappointed. Tweezers are paramount and should be learned and used as an extension of your body...those are your hands in watchmaking.

 

Suppliers like cousinsUK, ofrei, borel, esslinger and similar -- depending where you are hailing from -- are your main support...and don't forget ebay!

Edited by bobm12
Link to comment
Share on other sites
canthus Super WRT Addict

canthus

Posted
Posted (edited)

I too took up this hobby about 2 years ago.   I purchased cheap movements from ebay etc but found most were broken and struggled to find the faults then didn't know how to fix them!!.  After many old movements and still no working one I tried a different tack!   I purchased some low cost NOS movements in pairs or triples.  This allowed me to mess about with one but still have a good copy when things went wrong.

 

Try

www.globalwatchstraps.com  who have an ebay shop [email protected].

 

They are based in Netherlands but service is good and quick delivery.

Edited by canthus
  • Like 1
Link to comment
Share on other sites
Gary Super WRT Addict

Gary

Posted
Posted

I am thinking I need to go with the purchase those that are working. I am not sure on finding faults yet. I started about 3 months ago trying to purchase a tool here and there. 

I apologize to the Benrus and Westclox watch company for doing that to their watches. But I haven't given up!

 

Start with something working and move up!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • nevenbekriev
      Watch running too fast

      By nevenbekriev · Posted

      I am not sure for the terms in english, but if I directly translate from Bulgarian or Russian, there are 'magnetic soft' and 'magnetic hard' magnetic materials. The first group will not get magnetised, thow they will be attracted by magnets. The soft iron for example. The second group, like hardened steel, will get magnetised. So non magnetic hairspring aloys belong to the first group.
    • nevenbekriev
      Waltham A-11 Hairspring and Balance assessment help needed.

      By nevenbekriev · Posted

      Looks like it is only dirt. If rust, then this means the strenght of the spring is reduced in places with rust, so the spring is damaged and useless. Only light surface rust, which is rather residual from other places activity of rust can be cleaned, and no chemicals that can etch the metals of the spring aloy should be used
    • Waggy
      Case Tube Tool - Quest for one that works

      By Waggy · Posted

      Hello, I'm after some help on getting a functional tool for removing and replacing case tubes, the friction fit type not the threaded type. I have previously owned two Chinese Ali Express tools, which worked, but in each case after using on a watch case with an angle the watch had to be manually held perpendicular and when this angle was not perfectly aligned the pusher pin inevitably received a slight side load and the tool body was damaged. Due to the fact that the hole which holds the pusher pin is so close to the end of the block and the material wall is so thin: The result was that the hard pusher pin stretched and deformed the hole and the pusher pin was then slack and no longer perpendicular, and eventually the material split altogether. After I looked at the tool I realised that the block the hole was machined into was aluminum, this coupled with the extremely thin wall made this hole very weak and prone to the deformation and damage I had experienced. I looked to another reputable supplier (see below) who advertised their tool as "all steel" and I even contacted their customer support who confirmed that the block in question was made of steel. I was very disappointed yesterday when it arrived and found that it was in fact aluminum and not steel as promised. I could tell by the feel of the material (weight) and confirmed with a magnet which would not 'stick' and have since requested a return/refund. Assuming the return/refund goes smoothly, I am still left with my original problem of not having a tube pusher tool - does anyone have any recommendation for a tool which will work and will also stand the test of time?
    • Waggy
      Help for a novice - fused spring bar

      By Waggy · Posted

      Drilling is going to be difficult, firstly because the drill bits are so thin and brittle, expect to break a few. The second issue is access to the 'hole', as the other lug will be in the way, meaning that you will have to drill at a slight angle, putting a bending stress on the drill bit and with the slightest drop in concentration .... and back to my first point. I would be tempted to grind them flat with a Dremel type tool or small jewelers file, and then put a center punch in the center of the bit to be drilled so the drill bit doesn't skip around and break... but expect this to be slow and frustrating work. By the time you have done 4 of these you'll be an expert and can come back and tell us all the best way to do it if you go down this route. However, I would seriously consider What @watchweasol said and drill from the outside-in, this will ensure straight holes without having to work around the other lugs. It may be worthwhile making yourself a simple paper template so you can be sure to match the position of each hole before drilling. In the end you will be left with 4 holes on the outside of the lugs, but many cases are made this way and unless you are looking for it you probably won't notice or realise that it's not the way the watch was meant to be in the first place.
    • Waggy
      Pin pallet lubrication

      By Waggy · Posted

      What works for me (waiting for the villagers to assemble with torches and pitchforks) is to put a liberal (in watch terms) spot of 9010 on one of the pins of the pin pallet, this seems to improve amplitude and beat error.
×
×
  • Create New...