Jump to content

Colditz

Colditz

By Colditz
in Watch Repairs Help & Advice

 Share

Recommended Posts

Colditz WRT Addict

Colditz

Posted
Posted

Hi Mark

I have a Lancashire Watch Co. pocket watch, it has 7 jewels. The centre wheel as in your military Omega is loose due to a worn bridge hole which has elongated over time. There is no bush to remove/replace and I was wondering what the best course of action is. Do I fit a jewel in the bridge and if so what kit do I need.?

My nephew inherited the watch from his grandfather and of course it has sentimental value so I would like to get it working again for him.

The detail I have is: manufactured by the Lancashire Watch co Prestcot in 1901.

 

IMG_5100.JPG

IMG_5103.JPG

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

 

Has the pivot worn? If so, it needs to be put in a lathe and cleaned up. Providing it leaves a good size pivot. You can re-bush using a pocket watch brass bush or a jewel if you can find the correct size. The easiest is to fit brass. You could do this by hand by buying reamers or if you have a Jewel fitting tool you could use that, do not forget to remove any burr. No jeweling tool. You will need a flat end stake and small hammer and tap in. Jeweling tool you have the stakes so you select the right size.  

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • LittleWatchShop
      Movement holder made with 3D printer

      By LittleWatchShop · Posted

      Back home...printing now.  Will report results
×
×
  • Create New...