Jump to content

Another old cuckoo clock repaired ..

Deano6974

By Deano6974
in All Things Clocks

 Share

Recommended Posts

Deano6974 New Member

Deano6974

Posted
Posted

I recently posted an old cuckoo clock I repaired to full working order then I saw another that had the chains pulled too hard and were stuck in movement, so I stripped down removed and cleaned movement before re assembly and oiling, spent some time rubbing case parts down to bare wood and then re stained, bellows were both torn so replaced the paper on tops from a homemade template and ordered a new dial as original 70mm but decided I liked an 80mm instead so put that on anyway all in great working order and movement like new with no wear on pivot holes at all it couldn't of run for long considering its age Im guessing maybe 40's as after 1950 Im told the rear countwheel was put inside the movement.. 

WP_20181105_08_58_41_Raw.JPG

WP_20181108_22_29_19_Rich.JPG

WP_20181110_13_30_17_Rich.JPG

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      The cannon pinion (be it conventional style or what you see in this movement) should slip on its arbour so the hands can be set independently without affecting the gear train.  If there is too much friction between the cannon pinion and the second wheel, turning the hands to set them backwards can sometimes force the escape wheel teeth to overrun the pallet stones, creating the behaviour you describe. The train is running in reverse when this happens.  This can often chip the pallet stones. I’d say at least half of the watches I’ve inspected with very tight cannon pinions had chipped pallet stones. Hopefully this isn’t the case with your watch.  I’m not familiar with this movement but you need to get the friction in the cannon pinion adjusted correctly.  Hope this helps, Mark
    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      Pallet fork was in. I’d had the movement running ok, and only removed the balance to flip it over and install the keyless works and date mechanism. The pallet fork wasn’t locking the gear train when hand setting - it was oscillating as the escape wheel rotated. This may have been in one direction only - can’t remember. 
    • watchweasol
      Stem broken - can it be rescued?

      By watchweasol · Posted

      Hi   Find attached parts/repair notes for the JLC 911,  might be useful. JLC_JLC 910, 911.pdf JLC_JLC 910, 911 Repair Notes.pdf
    • watchweasol
      Intro

      By watchweasol · Posted

      Hello and welcome to the forum Dan. Used to know Middlesboro quite well, that was twenty years plus ago. Attached a little reading to get you started. TZIllustratedGlossary.pdf
    • JohnR725
      Can someone please explain watchmaker service mark interpretation?

      By JohnR725 · Posted

      for the most part no. Each individual watchmaker and/or shop had their own system. One of the shops I worked at basically had a reference to a page number in a book. then there are some shops that do no markings at all as they keep their records on a computer and they don't have to mark the watch. Usually if somebody is marking and they've service the watch before you'll see those next to each other. then as far as anything resembling a standard goes at one time the American watch and clockmakers Institute assigned all of their members a number. but that was a very long time ago and I doubt that they are using it anymore.
×
×
  • Create New...