Jump to content

Mainspring replacement

Folkvisor

By Folkvisor
in Watch Repairs Help & Advice

 Share

Recommended Posts

Folkvisor Super WRT Addict

Folkvisor

Posted
Posted

I recently tried to put a mainspring in my Waltham with rather disastrous results. I broke it by putting it the wrong way - my bad entirely...

It has a hole end spring and I found it difficult getting the hole over the cleat/pin on the barrel.

Any suggestions, tricks or incantations would be appreciated.

Dave

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Are you using a mainspring winder? If not I think, it depends on the best way for you. I have in the past hooked the spring on before winding it in. Fit the spring in about half an inch before the hook so when you go to wind it up the spring slips on the hook, in order to do this you do not need to fit the barrel into the movement, just hold it and wind it with pin tongs. In some cases, the hook part is too close to the barrel so it needs to be bent a little, but not to much as it will rub on the spring and wear through. I am sure with practise you will find your best way.

  • Like 2
Link to comment
Share on other sites
Folkvisor Super WRT Addict

Folkvisor

Posted
  • Author
Posted

Thank you for the advice.

Excuse my ignorance but what are pin tongs? Could I use small needle-nose pliers to wind the spring? I'm thinking even a large pair of tweezers would work.

I'm sure that after breaking a couple more springs I'll be pretty good at it.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
41 minutes ago, Folkvisor said:

Thank you for the advice.

Excuse my ignorance but what are pin tongs? Could I use small needle-nose pliers to wind the spring? I'm thinking even a large pair of tweezers would work.

I'm sure that after breaking a couple more springs I'll be pretty good at it.

Pin tongs or pin vices see here.

https://www.cousinsuk.com/category/pin-vices-chucks-tongs

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
×
×
  • Create New...