Jump to content

How do you reduce a plastic crystal diameter easily?

chriz74

By chriz74
in Watch Repairs Help & Advice

 Share

Recommended Posts

chriz74 WRT Addict

chriz74

Posted
Posted

I had to reduce the diameter of a sternkreuz glass from 30.3mm to 30mm or the retainer ring of the watch wouldn't fit. To do so I used sandpaper by hand (very tiring and time consuming) and for the final part I used the dremel with a sanding tip. Then I used the dremel and polywatch to polish.

Do you use a lathe to do this kind of job?

I thought if I could put the glass on the dremel maybe with a sucker then the process would be a lot faster and easier. I have another one that I want to try but by hand is too long.

advices?

Link to comment
Share on other sites
dman2112 Watch Enthusiast

dman2112

Posted
Posted
Did you do anything to solve?

Nothing tried yet. But I was going to use a lathe chuck to hold the crystal and chuck it in a variable speed drill and spin it while holding a sanding stick to the edge. Have not validated the theory yet so can't recommend


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

You can order a 3 or 3.1 crystal ,...or as you suggested , try to use a sucker in a drill or dremel . I had a similar situation where I wanted to turn a case back to put a finish on it and I got a small sucker from ebay that is used to prop a cell phone for viewing . I also went to the hardware store and Wal-mart and looked at the clear plastic suckers that are used on bathroom and kitchen racks .

Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted
7 hours ago, chriz74 said:

How did you attach the sucker to a dremel head?

Well , for mine ,  the sucker head to prop a smart phone had a wooden dowel that I attached to a drill . But the ones for bathroom racks have small gauge wire for the racks that can be cut and installed in a larger dremel collet....I think.

Link to comment
Share on other sites
Hamish Member

Hamish

Posted
Posted

Hi,

You might have it all sorted by now, but I have used this successfuly in the past. This is if you have a lathe.

(Hope that link copied over)

You do have to fiddle a bit to get the crystal central, but if you keep the speed slow it is not crucial. The other tip is to use the file across the work and not aligned with it. I learnt the hard way that crystals will be easily scratched if the file slips off the work. The plus side is that the crystal remains circular and you dont seem to compromise its fit as I think you would do with a dremel of sandpaper. The suction cup seems simple and a good idea too.

Link to comment
Share on other sites
  • 3 weeks later...
dman2112 Watch Enthusiast

dman2112

Posted
Posted

Update. I discovered an easy way. I just polish the outer diameter on my buffer that I use for case polishing. Very gentle and worked like a champ. I just spin the crystal around as I go and it remained perfectly concentric. I just kept checking with a caliper.


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Zendoc
      Which oiler to use

      By Zendoc · Posted

      I also find the red oiler in this set the most versatile size, but for cap jewels, I’ve found that the finer, Bergeon ergonomic oiler, 7013-N, gives me greater control over the amount of oil I’m depositing and gives me a more consistent drop size.  The yellow oiler is great for use as a probe - nudging pivots into place etc.  I’m about to file one down into a tiny tool to move the collet in adjusting beat.  Very handy, just too chunky to use as an oiler. 
    • Neverenoughwatches
      Cleaning after pegging jewels

      By Neverenoughwatches · Posted

      I switched to naptha a while back for that very reason, i only use alcohols for rinses now. 
    • mbwatch
      Jewel measurement and ordering sanity check

      By mbwatch · Posted

      Hi all - I am working on a Langendorf pocket watch movement which needed the lower balance hole jewel replaced. This is my first time reaming, measuring, ordering a new jewel and I need to check with you experts if I made a mistake in ordering or if ofrei made an error in selecting the jewel they sent me. I did a load of research to prepare for this repair. I reamed the hole up to a reamer measuring 1.19mm and my pivot measures 0.11mm. I ordered a convex olive hole balance jewel 12/120. I received the jewel in an envelope hand written 12/120. When I went to press in my jewel, it fell straight through the hole with ease. I measured it with the most accurate equipment I have and I am getting 1.00mm. So my novice question for you today is did I misunderstand the measurement and ordering or did the vendor send me the wrong diameter jewel at 100 instead of 120? Another way to ask this stupid question is should a 120 jewel order measure 120 or did I miss a detail?
    • Terrinecold
      Unknown fossil service

      By Terrinecold · Posted

      I measured the width at 2.05mm. The smallest wrench I have found so far is 2.5mm.     Just found that the imperial set has a 5/64” which will be just a tiny bit too small but a file should be able to fix that  
    • Neverenoughwatches
      Smoothing Broaches

      By Neverenoughwatches · Posted

      Yes all broaches are tapered, without the tapered length they would not broach evenly and the tapering does vary. Minimum to maximum broaching out sizes are quoted per broach.
×
×
  • Create New...