Jump to content

Maurice Lacroix Chrono Re-Finish

suj

By suj
in Watch Repairs Help & Advice

 Share

Recommended Posts

suj New Member

suj

Posted
Posted
Hi,

 

Real nice forum :) Just thought I'd post up a thread of a re-finish I'm doing on this Maurice Lacroix I picked up recently. Here is the watch:

 

IMG_20140624_144542.jpg

 

Overall, it was in really good condition, even came with 4 full size spare links which looked like they were brand new and had been taken off the watch at purchase and never used since. However the bracelet had seen some proper use. The case head isn't so bad, but does have some marks on the top. The sapphire crystal is flawless as I'd expect it to be. It keeps good time and the functionally the watch is perfect (it uses the ETA 251.262 quartz movement). The lume is amazing and the best I've seen in person on any watch. It charges very easily and lasts ages (after a 2 minute charge under a desk lamp/phone LED flash it can still be read like 4 - 6 hours later) 

 

But the bracelet! So I purchased a watch/metal polishing kit off ebay (this one to be precise). The entire watch has a brushed finish, however it's a really really fine brush - closer to the polished look, though you can clearly see the brush marks. A fine satin finish I guess is the best way to describe it.

 

Here's what the watch looked like when I got it. Note that the 2 links either side of the claps links are the new ones - so this is the finish I was/am trying to match:

 

PhotoGrid_1404494057590.jpg

 

And here's after going over the scuffed links with the co**BLEEP** and then fine buffing ball.

 

PhotoGrid_1404494184791.jpg

 

Although the finish is good - I've seen some watches with this level of "brush", it's not a perfect match to the OEM finished links - I guess I need a finer, higher grit buffing ball to use with the dremel. I will eventually tackle the head once I can get a better match on the finish.

 

Does anyone know if the same effect could be achieved by maybe polishing the links first, then using my fine buffing ball gently ? OR would it be better to find a finer buffing ball?

 

Cheers!

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Welcome to the forum suj, you will find this a friendly place to be a part of. There are folk here with diverse skills, so will undoubtedly pick up some good information.

That's a fine job you are doing refinishing the watch. When I refinish watches with brushed finish, I always polish them first to make sure that all the blemishes are removed before applying the brushed finish. I use very fine wet or dry abrasive paper or a fibreglass pen depending on the the effect that I want. Whatever method you use, ensure that the striations are parallel and follow the contours of the watch and/or bracelet.

Link to comment
Share on other sites
suj New Member

suj

Posted
  • Author
Posted

Thanks guys.

 

Yeah someone else also said polish the bracelet (to a mirror finish first) and then add the brush effect. When I've figured out how to get the finish I'm after I can work on the case head, which will make the watch look like new once it's done.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Thanks guys.

 

Yeah someone else also said polish the bracelet (to a mirror finish first) and then add the brush effect. When I've figured out how to get the finish I'm after I can work on the case head, which will make the watch look like new once it's done.

It takes a fair bit of time and effort to get the best finish, but it will be worth it. It would be a good idea to pick up a really cheap stainless steel watch with a stainless strap to experiment on. That way you can try out different grades of abrasives and polishes to see what suits you.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Michael1962
      Leaving the forum for a while.

      By Michael1962 · Posted

      Hope you mum keeps on mending. I was adamant that I was going to get myself going after my stroke. I was only 52. I still have a lot of life left to live. Some people give up. Some people don't let it beat them. Your mum sounds like one of the winners. 👍
    • Michael1962
      I'm going to be setting up a decent little workshop here at home.

      By Michael1962 · Posted

      Moved in. Now working out the best place to have things so moving around the room makes sense. The wooden movement testing rig may end up being suspended from the roof with some pulleys and ropes that I salvaged from some alfresco blinds that we replaced. I always seem to salvage things from things we scrap thinking, "I have an idea what I can use these for." I hope I'm not the only one that does that. My wife hates me for it. "What are you going to do with all this crap?" Anyway, here you go. If anyone has suggestions for workflow around a room, speak up. All Ideas are appreciated. The bench on wheels will carry either a laptop or my Samsung table for using with the little camera that is on the tripod for photos while dismantling etc. The small bar fridge in the corners going to have water etc in it and I might move the coffee maker from the kitchen out there as I am the only one that uses it. I want to get an ultrasonic cleaner so I may set up some sort of cleaning rig in front of the glass of the sliding door. Where the grandmother clock is currently standing. I'm hoping that I will be able to transition my working area, which is the table that the stool is sitting in front of, fairly easily between clocks and watches. I'll be doing my best to make sure that tools for each are separatedwhen stored. Logistics. I'll have a bit of wall space for being able to hang clocks if I find some that I wish to keep or hopefully at some time to be able to hang customer clocks for monitoring after servicing/repairs. The clock on the left in the blue pillow slip and the grandmother clock are earmarked for  Jarryd and his wife, Sara. He helped me move the benches in today. And then went on to tell me that ticking clocks drive him nuts. Who doesn't like the rhythmic ticking of a clock? I have a green pad for adding to the bench for a working surface. It is not a cutting mat or one of the Bergeon mats. It is actually a green desk writing mat. Was really cheap and will do exactly what I want, I think. I also have to get the sparkies back that put our new stove in to put some power points on the walls behind the benches. Hopefully this is all going to go well. I'm excited about it. It'll beat having to live out in the garage doing it. The other thing I have to do is cut a circle or square of plastic to go over the bouncing watch or clock part black hole in the middle of the floor. I would pretty much guarantee that anything that sproings off the bench would end up going straight down that drain. 😄      I think I have been on this forum about 4 years and still yet to really strike a blow. That's a bit sad isn't it. Signed up to Mark's watch course and have yet to buy the movement for working on. Have most of the tools I think I will need so now all just a matter of will.  
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
×
×
  • Create New...