Jump to content

Maurice Lacroix Chrono Re-Finish

suj

By suj
in Watch Repairs Help & Advice

 Share

Recommended Posts

suj New Member

suj

Posted
Posted
Hi,

 

Real nice forum :) Just thought I'd post up a thread of a re-finish I'm doing on this Maurice Lacroix I picked up recently. Here is the watch:

 

IMG_20140624_144542.jpg

 

Overall, it was in really good condition, even came with 4 full size spare links which looked like they were brand new and had been taken off the watch at purchase and never used since. However the bracelet had seen some proper use. The case head isn't so bad, but does have some marks on the top. The sapphire crystal is flawless as I'd expect it to be. It keeps good time and the functionally the watch is perfect (it uses the ETA 251.262 quartz movement). The lume is amazing and the best I've seen in person on any watch. It charges very easily and lasts ages (after a 2 minute charge under a desk lamp/phone LED flash it can still be read like 4 - 6 hours later) 

 

But the bracelet! So I purchased a watch/metal polishing kit off ebay (this one to be precise). The entire watch has a brushed finish, however it's a really really fine brush - closer to the polished look, though you can clearly see the brush marks. A fine satin finish I guess is the best way to describe it.

 

Here's what the watch looked like when I got it. Note that the 2 links either side of the claps links are the new ones - so this is the finish I was/am trying to match:

 

PhotoGrid_1404494057590.jpg

 

And here's after going over the scuffed links with the co**BLEEP** and then fine buffing ball.

 

PhotoGrid_1404494184791.jpg

 

Although the finish is good - I've seen some watches with this level of "brush", it's not a perfect match to the OEM finished links - I guess I need a finer, higher grit buffing ball to use with the dremel. I will eventually tackle the head once I can get a better match on the finish.

 

Does anyone know if the same effect could be achieved by maybe polishing the links first, then using my fine buffing ball gently ? OR would it be better to find a finer buffing ball?

 

Cheers!

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Welcome to the forum suj, you will find this a friendly place to be a part of. There are folk here with diverse skills, so will undoubtedly pick up some good information.

That's a fine job you are doing refinishing the watch. When I refinish watches with brushed finish, I always polish them first to make sure that all the blemishes are removed before applying the brushed finish. I use very fine wet or dry abrasive paper or a fibreglass pen depending on the the effect that I want. Whatever method you use, ensure that the striations are parallel and follow the contours of the watch and/or bracelet.

Link to comment
Share on other sites
suj New Member

suj

Posted
  • Author
Posted

Thanks guys.

 

Yeah someone else also said polish the bracelet (to a mirror finish first) and then add the brush effect. When I've figured out how to get the finish I'm after I can work on the case head, which will make the watch look like new once it's done.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Thanks guys.

 

Yeah someone else also said polish the bracelet (to a mirror finish first) and then add the brush effect. When I've figured out how to get the finish I'm after I can work on the case head, which will make the watch look like new once it's done.

It takes a fair bit of time and effort to get the best finish, but it will be worth it. It would be a good idea to pick up a really cheap stainless steel watch with a stainless strap to experiment on. That way you can try out different grades of abrasives and polishes to see what suits you.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
×
×
  • Create New...