Jump to content

Recommended Posts

Posted

Hi all, greetings from sunny South Africa. 

 

I'm looking for some advice on pall setting/alignment methods used for bulova accutron or eta/omega 9162 or similar movements. I have been serving / restoring these for a few years now and it's always a pain to align/set the alignment. 

If anyone could point me in the direction, or know of any documentation on official service procedures I would be greatly appreciative.

Regards, 

Jason Mauer 

1478800207125-1626113592.jpg

Posted

Hello Jason and welcome,

I saw Georges reference and have PM'd you a list of PDF's and a site reference, hopefully there are no problems.  I am in the process of creating an Accutron entry for the PDF / Document library and once Mark is back from Holiday he is amending my permissions to set it up and add other documents I have obtained in the public domain.

If you have been servicing them for a few years doubtless you have come across info I and others will be interested in.  I had difficulty up to the point where I bought a stereo microscope with 70x mag which was the the point where I was able to set the "draw" and phasing the accutron was more viable ie I could actually see the teeth on the index wheel.  I know others have managed with other types of magnifying devices but my eyes are not up to it. The site I referred you to:-

http://members.iinet.net.au/~fotoplot/acc.htm

is a gold mine of information and you could do worse than reading through it.  My thanks go to Rob Berkavicius and his co-writers for providing so much valuable information that set me off on the right path.

Cheers,

Vic

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Sorry to say it, but you’re very likely to break or lose something when servicing a wristwatch for the first time — I’ve been there! So, if these watches have any value to you, don’t attempt to service them as a beginner.
    • In writing "shimming the staff" I was alluding to the idea trailed in the above referenced thread of inserting a hair along the staff which, as the discussion there covered,  could result in some eccentricity. By making a (more or less) complete cylinder I was hoping to avoid that problem. Don't tell anyone, but needing a very ductile metal to do this by manipulation at such a small scale, I used a piece of an empty Tomato pureé tube! It occurred to me that the material's ductility(?) would also put less stress on the RT in forming a sufficiently tight seal. Anyway, that's how I avoided the temptation to use glue. No doubt your punctuational response to this confession will be "!!!" !
    • Hi All. I would appreciate some advice for a complete newbie on getting into watch servicing - nothing serious,  just as a fun project. I've got a thing for hand-wound watches and would like to bring an old watch (or two) back to life, so looking to learn to do a strip-clean-oil-assemble cycle.   I've toyed with this idea in the past (years ago) and picked up a couple candidates to learn on, but never found the time for them.  One is an old Ingersoll, swiss-made 17 jewels. It seems to wind and tick. Casing, dial, glass are in great shape, so looks like a good candidate to me for the first service. The other is a Benrus DR23. It winds and makes a few reluctant ticks, but then seems to stop. Casing looks like a complete gonner, and the dial is in pretty poor shape too. If the movement is not broken and just needs a service, I wonder if there's any possibility of getting a cheapo Chinese casing & dial to fit this movement in, or is it extremely unlikely to be the right size?   For a start, I want to strip & assemble a movement, perhaps a dozen times to build up the basic parts handling skills. I see that online advice is to buy a Chinese-made ST36 for this purpose. Can I just go at the Benrus or Ingersoll instead, or does it make more sense to get a cheap ST for this? Thank you.    
    • Hi,  I have this vintage Navitimer 806 with a bezel that plays a little bit as shown in this video: https://imgur.com/a/2NjdiF0 How would you fix this? I don't see where a gasket would fit for instance. Also, it seems this issue happens sometimes with older Navitimers.  Thanks
×
×
  • Create New...