Jump to content

Service Manual Or Oil Chart For Eta 954.111

rogart63

By rogart63
in Watch Repairs Help & Advice

 Share

Recommended Posts

rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

I am about to service a ETA 954.111 movement . The canon pinion is stuck.That is probably why it only ticks a few minutes before it stops?  Hope i can remove it? And would like to find a oil chart for it? Found this 

file:///C:/Users/admin/Downloads/3925_ETA%20954.101,954.111_smaller.pdf 

But need to find the manual for 954.111 or 954.101 

Edited by rogart63
Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
  • Author
Posted

Do you think it's okay to oil the jewels and keyless work? Have search but can't find anything . This ETA movement was in Omega,Tissot.Eterna,Certina and many other watches . Would be great with a picture of the date ring side. I am not 100% sure how the bits should be put together?

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
  • Author
Posted

Hi rogart,

 

did you try cousinsUK. They have a lot of movement service data for download. I'm at work, otherwise I would look it up.

 

Cheers,

 

Bob

I did. But only found a parts list and a electronic tester. I have put it together again. Oiled it like i do with a manual movement. Wth 9010 and 8300 for the keyless work. And it's working :) Will put the result up when i have some new crystals for the cases. 

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted

Excellent...I would have recommended the moebius quartz oil but I guess if it is working...

 

ol241.jpg

Moebius Synthetic Quartz Watch Oil

 

Cheers,

 

Bob

 

For the most part all of the eta quartz watches should be similar for lubrication. So you could have used a 955 manual for lubrication guide. So their recommendation for the gear train is Moebius 9014 or Moebius 9034. Moebius 9014 oil is a mixture of 70% Moebius 9010 and 30% Moebius 9030 which causes it to have a lower viscosity than standard 9010.  So basically Viscosity of 9010 is either 120 or 150 depending upon your reference. In Moebius own publications they actually have different numbers. Then the 9014 is 98  and 9034 is 58. Basically they're looking for a low viscosity  synthetic oil.  What's interesting is they're not recommending Moebius 9000 With the viscosity of 100  which is specifically recommended for quartz watches.

  • Like 1
Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
  • Author
Posted (edited)

For the most part all of the eta quartz watches should be similar for lubrication. So you could have used a 955 manual for lubrication guide. So their recommendation for the gear train is Moebius 9014 or Moebius 9034. Moebius 9014 oil is a mixture of 70% Moebius 9010 and 30% Moebius 9030 which causes it to have a lower viscosity than standard 9010.  So basically Viscosity of 9010 is either 120 or 150 depending upon your reference. In Moebius own publications they actually have different numbers. Then the 9014 is 98  and 9034 is 58. Basically they're looking for a low viscosity  synthetic oil.  What's interesting is they're not recommending Moebius 9000 With the viscosity of 100  which is specifically recommended for quartz watches.

Perfect . I will order that the next time i take something home from Cousinsuk . I am about to fix a 955 movement that is not working okay. It get stuck when the date comes to 25 and stops . When i wind it past 25 it works again until next month. Its my own watch.

Edited by rogart63
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • DDean
      First Project Already A Bit "Sideways"

      By DDean · Posted

      I will try this weekend.  I've tried several times with my cell phone and it's just too small and recessed to get a good picture.  I need to get my macro lens and tripod out and then figure out how to get enough light down the hole in the side of the man plate to  actually show the top of the broken screw. I appreciate the effort and will try and get that pic this weekend.
    • RichardHarris123
      Simeon from Down Under

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Simeon
      Simeon from Down Under

      By Simeon · Posted

      Hi,   My name is Simeon I am based in Sydney, Australia and have recently got into watch repair / watch making.  I am very much a learner having serviced multiple forgotten watches, some of which were actually successful!   I have a slowly growing collection of watches, mainly old Soviet, a few Japanese and (not pictured) some Raketas, a Poljot Alarm, an Omega Speedmaster Reduced and a vintage (1972) Tissot Seastar.  I like unloved vintage watches, with quirky faces and enjoy bringing them back to life through the simple(!) act of disassembly, clearing and reassembly. I am an Electrical Engineer who also undertook a trade apprenticeship so I am reasonably handy - It's fair to say, I know just enough to get myself in trouble. 
    • Waggy
      Chinese clone demagnetizers

      By Waggy · Posted

      ha ha looks like a WMD.....you know I want one now  
    • Simeon
      Citizen Cosmotron X8 04-4800 Fault finding

      By Simeon · Posted

      I took a chance on a non running Cosmotron X8 ("perhaps just needs a new battery" said the advert). Sure enough, I open it up and it has the wrong battery installed (a Renata 344 rather than the correct Renata 386) and the screws holding the battery contact had been sheared off to half a head on both ends. Ho ho, I thought - there's the problem. I got the broken screws out easily enough and as soon as I placed the correct battery in place the balance started. This picked up speed when I reinstalled one side of the battery contact and looked like it was a runner. As I was trying to get the replacement screws in, I did one side but the second was a bit of struggle (hold down the battery contact against its spring while dropping the screw in with tweezers) the balance stopped again. This time it wouldn't start again. 98 percent sure that I didn't stick anything, anywhere important or break it in a mechanical way. The battery was in place for most of the struggling with the contact, so it might have had an intermittent connection which could have upset the electronics. I tried giving it a puff with the blower but the balance doesn't seem to rotate in the normal way, it seems to be held in a static position by magnet. It can be pulled out of this position but spins back and stops dead. This may well be correct for all I know. Anyway, does anyone know anything about these watches and can tell me how I would go about and fault find this? I will be servicing it at some point so should be able to rule out mechanical issues from an old watch but not sure where to start with the electrical part of it.
×
×
  • Create New...