Jump to content

Full Plate Movements And Pivot-Jewel Fitting


Edmund

Recommended Posts

Dear friends,

 

What is the correct method for fitting all pivots in all jewels in a full plate or 3/4 movement like the one below, a Phenix from 1908.

 
Sadly for it, some pivots and jewels were badly damaged as I was unable to align them properly during re-assembly.
 
Although it is too late for this Phenix, your comments may help to prevent a similar 'disaster'.
 
Many thanks.

post-1450-0-89943700-1448201352_thumb.jp

Edited by Edmund
Link to comment
Share on other sites

Hi Edmund,

 

I know exactly how you feel and I emphasize wholeheartedly.

 

Now do not despair, Bergeon has developed a tool just last year. It is a special, very rare and specialized tool to do exactly that and the good news is they are selling it cheap contrary to their normal price list policy: it is only $2000.00 and a waiting list of 6 month, special order! Now you must hurry since the Swiss embargo might just make it impossible to source after December and you may be forced to buy a same exact Chinese copy for $0.99 on ebay! Just kidding! :)

 

Honestly, my recipe is patience and more patience, be gently and don't force anything. Try often the wheels involved for free running until everything feels good. Those bridges could be a bear to put back...luckily a gentle bear...not like some mainsprings by hand. In any case, I welcome you to our site -- I haven't done that before -- and hope another member has a better system to do what you ask.

 

Cheers,

 

Bob

 

PS. I'm really not aware of any tool that allows you to do what you want, really. The Bergeon thing is simply making fun of their stuff...those in the know realize what I mean! :)

Link to comment
Share on other sites

Make a miniature version of a clock pivot aligning tool by heating the tip of an old oiler and bending it to look like this.

post-124-0-24736300-1448208004_thumb.jpe

This will allow you to push and pull pivots while very gently applying downward pressure to the plate.

  • Like 1
Link to comment
Share on other sites

Make a miniature version of a clock pivot aligning tool by heating the tip of an old oiler and bending it to look like this.

attachicon.gifimage.jpeg

This will allow you to push and pull pivots while very gently applying downward pressure to the plate.

This is the kind of tool I was missing. Stupid me...  :pulling-hair-out:

Link to comment
Share on other sites

Patience, patience, patience, patience, patience, patience, swearing, tantrum, more swearing, referring to Roger Mellie's Profanisaurus (now available as an app by the way), outrageously insane swearing, mental breakdown, therapy, patience, patience, patience, patience, patience etc..........

 

Works for me every time.

  • Like 3
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This makes much more sense now, the oil is withdrawing itself to make as little contact with the epilame as possible. Same principle as wax on a car creates a hyrophobic surface that makes the cohesive properties of water molecules pull together.  The water beads run off only when under the influence of gravity but still remain cohesively beaded up. And as mentioned earlier a pivot would keep the oil in place on a cap jewel.  Epilame on an escapement would be a different scenario, there is nothing to hold the oil in position if gravity tugs at the bead to move, plus the escape teeth pull the oil about Maybe this is why its suggested to run the watch for a short while to remove the epilame to make two oleophobic surfaces either side of the oil, creating a ring of fire 🔥 around it 😅
    • As with every skill it watchmaking, it takes practice. Notice at the top of the document it says, "Practical work - 40 hours".  I can get the balance wheels 'close enough' to flat, but never seem to get them perfect. Same with gear wheels. Guess I need more practice.
    • Has it got a beat adjustment on the platform or is it a fixed hairspring? in short what you are looking at to get it just about in beat is to get the roller jewel sitting dead centre between the banking pins. So remove the platform and take of the pallet fork and escape wheel to give you clear line of site, sit the platform with the balance in place and with it level look between the banking pins and see if the roller jewel is sitting between them, if it is nice and central its there or there abouts in beat, if its not the the position of the pinned end of the hairspring needs to be adjusted to move the roller jewel into the correct position, thats why I asked if it has an adjustment on the platform or not, if it has its an easier job. 
    • I've managed to adjust it. I'm going to try and explain it as well as I can with my limited horology knowledge but I hope it helps someone in the future. There is a cam to the right of the front plate as shown in the picture. As the clock ticks along, the pin indicated in the gear comes around and slots into one of the silencer cam gaps, turning the cam. The pin completes a full rotation in 2 hours. To adjust the cam to start at the right time set the clock to just before 7. I did 6:45. Then I turned the silencer cam anticlockwise, which spins freely, until it pushed the silencer lever up and was placed just before the drop. Just before the 7AM indicated in the picture. All I then had to do was progress the hands to 7-7:15which made the pin slot into the silencer cam gap and turn the cam so the lever comes down again, unsilencing the clock. That was it. If anyone comes across this issue again I'd be happy to assist. Thanks again to everyone that helped. Hey Transporter! Thanks a lot for the reply. That was a really good explanation and I'm sure it would have made my troubleshooting a lot less painful haha. I'm sure someone will find it useful in the future. Thank you again for taking the time to try and help me out with this.
    • Now I'm completely confused, it would appear that the epilame  is oleophobic  as @Marc states: This oleophobic  behavior can be seen as beading of the droplet (as above) which stops the oil spreading which is supported by what we observe on treated/untreated cap stones (for example), but as @VWatchie states this should make the drops more mobile and is supported by the literature:   A review on control of droplet motion based on wettability modulation principles design strategies recent progress and applications.pdf   However the whole point is that we have less mobile oil so an oleophobic  would see to be the opposite of what we want. In fact this beading and high mobility are desirable properties in things like smart phone covers, see below.  I am fairly sure that epilame doesn't make the droplets more mobile, so maybe its a strange coating with dual properties that are both oleophobic (beading) and cohesive/adhesive resulting in low mobility?? This may explain the high price??  
×
×
  • Create New...