Jump to content

Recommended Posts

Posted

My grandad passed away and left me his Swiss Emperor watch that he used to wear. While it’s not valuable, it holds a lot of sentimental value for me. The watch is quite worn and would need some restoration work (though I know this may not be the right place to discuss that).

I took it to a repair shop today, where they tried a new battery but called it a "non-starter," saying there wasn’t much that could be done. I’d like to know if it’s worth seeking a second opinion on this watch.

IMG_5924.jpg

IMG_5925.jpg

IMG_5923.jpg

Posted
35 minutes ago, Theoldgold1997 said:

I took it to a repair shop today, where they tried a new battery but called it a "non-starter," saying there wasn’t much that could be done. I’d like to know if it’s worth seeking a second opinion on this watch.

If you just took it to somewhere that replaces batteries then they don't normally have much of a clue what they're doing.

  • Like 2
Posted

Hi there are several things you can do, first get the back off  and check the battery terminals, should be clean as should be the battery compartment.  Two get hold of a line release machine / tester and rotate the hands, this will check the freedom of the movement and also detect the circuit pulse. It may be the coil is dead. Sometimes done when removing the back to change the battery

The testers can be found on eBay and Amazon. Around £23 to. 25.

  • 4 weeks later...
Posted
On 10/28/2024 at 7:48 PM, Theoldgold1997 said:

there wasn’t much that could be done.

There's nearly always something that can be done, it's just a matter of finding someone willing and able to do it, and the cost associated. And quartz watches aren't usually very costly, even if the whole movement needs to be replaced. I recently replaced a AU$25 movement in a colleague's favourite $200-$300 watch after she had been told it was not repairable. Made me look good, but why was she told that in the first place? I can only imagine that she took it to a jeweller who only does batteries and bands. You might like to let us know where in the world you are, and perhaps a nearby member here would be able to see to it for you. (On  the off-chance you're in Western Australia, I would be pleased to have a look myself!) The watch might not be valuable to anyone else, but if it's valuable to you then it's worth fixing, I think.

As has been said, if you feel confident removing the case back, take a good close-up photo of the movement that identifies any print or numbers on it. That'll let us at least identify whether the movement is designed to be serviceable and what a movement replacement would involve.

Posted
2 hours ago, GPrideaux said:

There's nearly always something that can be done, it's just a matter of finding someone willing and able to do it, and the cost associated. 

I use my idiom at work in relation to this....." Anything is possible when you throw enough money at it "

On 10/28/2024 at 12:25 PM, AndyGSi said:

If you just took it to somewhere that replaces batteries then they don't normally have much of a clue what they're doing.

Oh so true, my Missus MK watch when it came to needing it's second battery replacement.....had a whacking great thumbprint across the battery that i was taking out and the top plate. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
    • Seems like he doesn't have the micrometer cap  attached to the spindle so he can only push down but cannot pull up? If the cap screws into the spindle I guess you don't need the spring? I only have a "normal" Seitz so I really have no idea. 
    • Do you have a part number for the bearing shim lock tool?
    • Yes in my opinion the 3/4HP is plenty but it’s your decision & yes it does come with speed control but foot operation so my reason for changing to potentiometer was because my leg shakes so it was like me revving the lathe & anyway I prefer to set the speed. I & a few others that I recommended the motor to run a Pultra 10mm lathe so if you have a 6 or 8mm B & L then it will be plenty, if you have seen any of my videos you will have seen that when using a graver I run quite slow without any problems. Dell
×
×
  • Create New...