Jump to content

Cleaning/replacing/... a mainspring when still learning the ropes

LuigiMeister2800
 Share

Recommended Posts

LuigiMeister2800 Member

LuigiMeister2800

Posted
Posted

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

Link to comment
Share on other sites
Malocchio WRT Addict

Malocchio

Posted
Posted

You could just buy a couple of the most common sizes. Best Chinese sets are allegedly good. Manual mainsprings are easy to wind by hand but automatic springs are trickier because of the bridle in the end. Buying new springs is also an option. 

  • Like 1
Link to comment
Share on other sites
rossjackson01 Super WRT Addict

rossjackson01

Posted
Posted
23 minutes ago, LuigiMeister2800 said:

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

Watch the YouTube videos in how to hand wind.

It was 15 month before I obtained a set of winders. Only used them unsuccessfully since. 

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi Maloccio has given the options, I still do it by hand, but if you are not sure just buy the winder to suit you purpose at the time. That way over time you will build a collection of the ones you use the most and. Not some ornaments which never get used.

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
1 hour ago, LuigiMeister2800 said:

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

All depends what you are working on. If the right mainspring is available and the money to buy one each time isn't an issue then a new one would be the best option. Downside is you dont get to aquire the skill of winding mainsprings. Which eventually if you work on a lot of old watches you will need.

28 minutes ago, watchweasol said:

I still do it by hand,

Yey old timer, my hero 👍

1 hour ago, LuigiMeister2800 said:

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

In my eyes leaving it in the barrel isn't an option, when I started i thought about it and i tried it. I soniced the barrel upside down in the hope it would clean it, it did but not to an acceptable level at all. No way are between the coils gonna get clean or all of the bottom of the barrel. You have to bite the bullet and just get stuck in, have it out and hand wind it back in if there's no option of a winder. Practice ,practice and practice and when you're done practicing......... you've guessed it , practice some more.

  • Like 2
Link to comment
Share on other sites
CYCLOPS WRT Addict

CYCLOPS

Posted
Posted

I think you should acquire some mainspring winders, you use/need them in the future, hand winding is a last resort for what ever reason, too much distortion especially from beginners, I think sometimes it is better to hand clean with arbor out and reassemble than hand wind, but I have winders so just my opinion.....new is a great option like Neverenough said...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Pallet jewel

      By Neverenoughwatches · Posted

      The entry and exit stones have different impulse face angles  murks.
    • Waggy
      First Project Already A Bit "Sideways"

      By Waggy · Posted

      Depending on how much of the screw is left, you may be able to screw it further in and it may fall out of the hole that the dial foot sat in. To do this I rough up the tip of the good screw and screw it in, often the rough surface of the good screw and the rough surface on the broken screw get enough of a bite to transmit the torque into the broken section and force it out the other side. Like I said the size of the broken screw needs to be in your favor, but you never know you may get lucky.... or if you get it moving you may be able to then back it out with a screwdriver taking a bite on the rough surface. worth a try
    • DDean
      First Project Already A Bit "Sideways"

      By DDean · Posted

      I will try this weekend.  I've tried several times with my cell phone and it's just too small and recessed to get a good picture.  I need to get my macro lens and tripod out and then figure out how to get enough light down the hole in the side of the man plate to  actually show the top of the broken screw. I appreciate the effort and will try and get that pic this weekend.
    • RichardHarris123
      Simeon from Down Under

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Simeon
      Simeon from Down Under

      By Simeon · Posted

      Hi,   My name is Simeon I am based in Sydney, Australia and have recently got into watch repair / watch making.  I am very much a learner having serviced multiple forgotten watches, some of which were actually successful!   I have a slowly growing collection of watches, mainly old Soviet, a few Japanese and (not pictured) some Raketas, a Poljot Alarm, an Omega Speedmaster Reduced and a vintage (1972) Tissot Seastar.  I like unloved vintage watches, with quirky faces and enjoy bringing them back to life through the simple(!) act of disassembly, clearing and reassembly. I am an Electrical Engineer who also undertook a trade apprenticeship so I am reasonably handy - It's fair to say, I know just enough to get myself in trouble. 
×
×
  • Create New...