Jump to content

Bergeon 4266 maintenance?

MartinOfPrague
 Share

Recommended Posts

MartinOfPrague Member

MartinOfPrague

Posted
Posted

Hello, I bought a used Bergeon 4266 crystal lift, and there is a problem - it looks that the jaws do not grip the acrylic crystals sufficiently and in most cases, they slip even at the lightest attempt to tighten. I examined the brass jaws under a loupe, they seem worn to me. Is it possible they need to be sharpened (shaped), like screwdrivers? Is it even realistic to do so without special tools? Or was it downright bad idea, to buy this kind of tool used?

Geotex WRT Addict

Geotex

Posted
Posted

Are you certain you are using the tool in the right circumstances? Many (most?) crystals are not shaped appropriately and should just be pushed out manually for removal and inserted using a press tool rather than a lift. Front-loading movements that specifically require a lift will use crystals that have sufficient flat surface on the side of the dome to accomodate the lift. Another point is that if you are using a lift for insertion, the lift must engage part way up the side of the crystal rather than flush with the base. The lifts are initially sold with shims or jigs in order to accomplish this, but those may not be included when you purchase a used lift.

  • Like 1
  • Thanks 1
mikepilk Distinguished Member

mikepilk

Posted
Posted
1 hour ago, MartinOfPrague said:

Hello, I bought a used Bergeon 4266 crystal lift, and there is a problem - it looks that the jaws do not grip the acrylic crystals sufficiently and in most cases, they slip even at the lightest attempt to tighten. I examined the brass jaws under a loupe, they seem worn to me. Is it possible they need to be sharpened (shaped), like screwdrivers? Is it even realistic to do so without special tools? Or was it downright bad idea, to buy this kind of tool used?

The internal rubber gasket has perished. I had the same problem. Cheap and easy to replace

image.thumb.png.1a4bf9227d0c46ba9156962f26da7fb2.png

  • Like 3
tomh207 Distinguished Member

tomh207

Posted
Posted

It’s not a big problem to strip it, clean, lube and replace the ring. It’s the cheapest bergeon thing I’ve bought so far.

 

worth doing, mine works really well now

 

Tom

 

IMG_0163.jpeg

IMG_0167.jpeg

  • Like 3
mikepilk Distinguished Member

mikepilk

Posted
Posted
25 minutes ago, Geotex said:

Are you certain you are using the tool in the right circumstances? Many (most?) crystals are not shaped appropriately and should just be pushed out manually for removal and inserted using a press tool rather than a lift. Front-loading movements that specifically require a lift will use crystals that have sufficient flat surface on the side of the dome to accomodate the lift. Another point is that if you are using a lift for insertion, the lift must engage part way up the side of the crystal rather than flush with the base. The lifts are initially sold with shims or jigs in order to accomplish this, but those may not be included when you purchase a used lift.

I use the crystal lift to fit all my acrylic glasses. You need to use the base to make sure you grip the acrylic in the right place, to avoid damage. I would try fitting with a press tool as shown in the Sternkreuz catalogue.  I could use my cheap caseback press for the top plate, but I don't see anywhere to buy the lower convex rubbers pressure plates. It says it should be about half the size of the upper plate, but Cousins only show convex sizes of 38mm +.

 

image.thumb.png.2ceebc31739ef55bab566989d372b71b.png

 

image.png.8df5cebbd2d213630e216bf4c4e55cba.png

  • Like 2
MartinOfPrague Member

MartinOfPrague

Posted
  • Author
Posted (edited)
46 minutes ago, Geotex said:

Are you certain you are using the tool in the right circumstances? 

Thanks @Geotex! My tool came with a shim/jig (even with the adaptor for oval-shaped crystals), but I did not know the crystals for front-loaders Are shaped differently.

So, is there a common view among watchmakers that crystal lifts should be used for front-loaded watches only? As a newbie in watchmaking, I thought crystal lift could be the easiest way to replace a crystal which is cracked of scratched beyond polishing - without the need of taking movement out of the case.

37 minutes ago, mikepilk said:

The internal rubber gasket has perished. I had the same problem. Cheap and easy to replace

image.thumb.png.1a4bf9227d0c46ba9156962f26da7fb2.png

Thanks. I disassembled the tool and indeed I noticed the gasket is very tired, I just wasn't sure how big is the impact to the usability of the tool. I will order a new gasket, then.

Edited by MartinOfPrague
tomh207 Distinguished Member

tomh207

Posted
Posted

Whether front loader or not this tool is for acrylic crystals without a tension ring. You also want the jig that will hold the crystal correctly so you can pick up the new crystal correctly using the crystal lift.

 

one of these

Tom

 

 

IMG_0221.jpeg

  • Like 1
MartinOfPrague Member

MartinOfPrague

Posted
  • Author
Posted
2 hours ago, RichardHarris123 said:

Photos would help. 

Here are the pictures. I hope you can judge something from them. The last one is the poor old beater I am practicing with – not the best crystal shape for a crystal lift indeed, I reckon.

2024-01-28 20.35.03.jpg

2024-01-28 20.35.47.jpg

2024-01-28 20.40.01.jpg

I also noticed these notches in the aluminium body of the tool, they look like an excessive wear rather than design feature to me, but I am not sure. Could they be a part of the problem?

2024-01-28 16.54.07.jpg

  • 2 weeks later...
Yani365 New Member

Yani365

Posted
Posted

The tooth edges look ok. You don't want them so sharp that they actually cut into the crystal. Rather, the force these apply is inward towards the center point of the crystal.

The jig that #Tomh207 shown above is used to allow a space below the lift when using the lift to install the crystal. This ensures that the crystal edge will have enough exposed edge to enter the case edge. 

Some crystals will have too much of a slope to allow the jig to put force towards the center without slipping off. Those crystals will usually be able to be removed by hand, pressing them out from below. If needed, a press could be used, gently, to remove the crystal. Reinstalling those crystals may require a different tool than the lift you have. #Mikepilk shows that tool above.

Let us know how it works out!

  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • TimeWerks
      Omega sweep second pinion friction spring - correct tension IS important

      By TimeWerks · Posted

      Thanks for this post MikePilk, I just came across a similar problem with an Omega 1022.  The problem I had was the seconds pinion spring was bent out of shape and did not even engage with the wheel properly, so the seconds hand was not moving at all. (no power loss though :) I removed the automatic module so I could access the spring and work on it. Once I bent it back close to the right shape, I experienced the same problem you reported about power loss.  Many tweaks later, and the seconds hand is moving properly again, with amplitude back to good numbers again. Cheers
    • caseback
      Clock newbie

      By caseback · Posted

      After cleaning up the pivots, I made bushes on the lathe. At this point I've pressed in 6 bushes (3 sets) and the wheels turn smooth. What I can also tell you, is that I'm not looking forward to final assembly. Getting the pivots aligned seems to get exponentially more difficult with each wheel that is added.
    • JohnR725
      Greetings from Whidbey Island.

      By JohnR725 · Posted

      Islands are interesting places to live depending upon their size and other factors. This is a bigger island and it has a bridge to get there at least on one end. It's also big enough that you don't have to go someplace else to get things typically. It can be a problem if you get a job in Seattle though. Yes I've known of people who commuted from the island to Seattle for a job and I don't quite remember how many hours it took but it took a long time. So basically islands are nice if you don't have to leave very often.
    • VWatchie
      What's your thoughts on this Rolex Sea-Dweller, ref. 16600, calibre 3135 project?

      By VWatchie · Posted

      Thanks @JohnR725! Everything you say makes a lot of sense and is encouraging to read.
    • JohnR725
      What's your thoughts on this Rolex Sea-Dweller, ref. 16600, calibre 3135 project?

      By JohnR725 · Posted

      isn't it nice to have a decent case open or when the case doesn't want to be opened? In the case of a Rolex watch that supposed to pass specific water resistant testing you probably do need to tighten the back down. But they shouldn't be tightened so much that they risk stripping the threads out. Then the other problem that comes up is the gaskets can start to disintegrate and then getting the back off can be quite a challenge unless you have a really good tool and perhaps some penetrating oil to loosen things up. Yes really nice case marking. When I was in school we were taught to mark the cases and  the American watch and clockmakers Institute even had a? So if you joined at one time they would give you an identification number. They were explaining or giving an example of if the watches ever found in you have a unique number they can perhaps figure out the history of the watch or identify the body it's attached to for instance not that that probably comes up that often. So you got a unique number and even made a special metal stamp that you can purchase. It wasn't a super big aggressive stamp but still it left a mark in the back of the case. Then I heard from people at work on Rolex watches they were using a felt pen indelible but later on they decided that was bad because apparently the ink could release  chemicals although it seems like once it's dry that shouldn't be an issue. Then of course today was nice is you can keep computer records sealed have to mark anything at all I personally find it's best to leave no reference behind that you were even there. Especially when you have a beautiful watch that has no markings at all and now it has your scribbling all over it not good typically if there is a typical and watch repair?  a lot of minor repairs you don't need to do a complete servicing. But beyond a certain point you're going to have to take apart a lot of stuff you're going to disrupt the lubrication even if it looks perfect right now and yes you might as well just go ahead the service the whole thing. also in a watch like this where a lot of things seem to be going on the complete service would be better then you'll know exactly where you stand versus dealing with unknown mysteries for prior repair.
×
×
  • Create New...