Jump to content

Al from UK. Rheostat help required with watch cleaner.


HairyAL

Recommended Posts

Good afternoon everyone. I hope you are all well. I have been contacted by an elderly gentleman who is looking for a replacement Rheostat for his British made Electric watch cleaner.

The information i have for it is that it is based off frame No' 20, 

HP .006 motor

230 volts

50 cycles.

Please see below a pic of the Rheostat in question. Would anyone know the values of it in order for me to match them up with a possible replacement.

 TIA, 

Have a great day everyone.

 Al

 

IMG_20231207_140826.jpg

IMG_20231207_140849.jpg

IMG_20231207_140859.jpg

Link to comment
Share on other sites

Personally I doubt it. It doesn’t look like anything I recognise and I worked in electronics/electrical engineering 8 years or so back in the 70’s/80’s.

 

you may struggle with this one unless you have a part number and the manufacturer to find a possible modern manufacturer.

 

 

Link to comment
Share on other sites

28 minutes ago, RichardHarris123 said:

My knowledge is limited but I believe you need a rheostat that is rated at 240V minimum and the correct power (W). Do you mean. 006 horse power, if so about 4.5 W so 5W will suffice. 

It’s not necessarily as simple as you put it Richard, I doubt very much that that motor would be 5W, wouldn’t pull a kipper off a plate 🤪😂

 

Tom

  • Haha 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • His reply seems quite honest and fair. Whats his feedback like ?, i tend to buy into the seller more than into the sale. Though i do take risks occasionally if i have a gut feeling  i can do ok. Missing and damaged stem can be a red flag but can also mean something quite innocent such as a stem release/set lever screw has come loose and the stem has fallen out and been lost over time. Missing crowns can be less of a problem.  One of first things we do when receiving a watch is to try the wind and set functions and rotate the watch back and forth to see if the secondhand starts up. These are good internal indicators that you may get away with only a service to carry out. Things i personally usually avoid are damaged fancy shaped crystals , heavy case damage, watches with certain damaged/ missing internal parts( parts that can't be self maufactured by the average repairer )The idea is to build up a good stock of commonly comsumable parts, this would be, crystals, balance staffs, watch stems and crowns, springs ( setting and shock ) , watch jewels inc. Caps, impulse and pallet stones, timing washers, all kind of screws.  Those are mostly at beyond a beginner level requirement .
    • We do need more photos but the spacer does seem to be behind the lip.
    • Cant tell if its a lip or a section of thread. If it is lip, then i can only think that the slotted ring is spacer for the armoured crystal to push up to. There isn't much info out there about www crystals. Generally they are popped off with air compression of a sealed case.
    • I was thinking that may be a thread. Would need more hotos to confirmM maybe @B1N9S can tell us whether that 'lip' goes all the way around or whether it tapers off like a thread?
    • Well done Sam, you've successfully completed a tricky piece of work there 👍
×
×
  • Create New...