Jump to content

Re-sizing a mainspring

Neverenoughwatches
 Share

Recommended Posts

Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted

Eyup watch peeps, i hope everone is well. I've just had a random idea maybe crazy ? ( hey I'm a bit fruit loop what can i say ). It dawned on me today while playing with a mainspring punch that a mainspring could theoretically be adjusted not only in length but also in height. If coiled and retained it could be ground or lapped to size ( yes I'm leaving out loads of details on the process so start thinking ). What are people thoughts ?  Barmy ? Or,  you may just have something there ? 

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

Done it numerous times. There's a limit how much you can take off, and the sides become sharp rather than rounded and that has to be addressed. You can't take a 2.00mm spring down to 1mm for example, there won't be a hole anymore. I've only done it when there was simply no other option, typically ultra thin pieces. You really have to glue (I use black Loctite super glue) it to a flat support, and have a bit of a method to keep it uniform. If you don't glue it down, inevitably the center coil becomes thinner than the rest. Of course you have to grind a bit, then unglue and reglue the other side and do the same. It's a hassle, but can save the day.

  • Like 1
Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
  • Author
Posted
17 minutes ago, nickelsilver said:

Done it numerous times. There's a limit how much you can take off, and the sides become sharp rather than rounded and that has to be addressed. You can't take a 2.00mm spring down to 1mm for example, there won't be a hole anymore. I've only done it when there was simply no other option, typically ultra thin pieces. You really have to glue (I use black Loctite super glue) it to a flat support, and have a bit of a method to keep it uniform. If you don't glue it down, inevitably the center coil becomes thinner than the rest. Of course you have to grind a bit, then unglue and reglue the other side and do the same. It's a hassle, but can save the day.

Thanks Nicklesilver, i just wondered if it was possible 🙆, the details i can now play around with. The main issue i figured would be getting rid of the burr.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Rather silly if you ask me. If you do not do it right then the spring will not be the same strength from end to end, it could even cut or mark the coils or the inside of the barrel and the underside of the barrel lid. Why not just buy a spring if you cannot get the correct height get the next to it. There are plenty of places on the internet to search. Even members on here help out with stock.  

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
  • Author
Posted
1 hour ago, oldhippy said:

Rather silly if you ask me. If you do not do it right then the spring will not be the same strength from end to end, it could even cut or mark the coils or the inside of the barrel and the underside of the barrel lid. Why not just buy a spring if you cannot get the correct height get the next to it. There are plenty of places on the internet to search. Even members on here help out with stock.  

Ahh more to think about, i didn't expect it to be easy. It was only an idea to see if it was possible, i also have thousands of springs .

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Bezel removal tool (chinese) problems

      By rjenkinsgb · Posted

      I've got a similar one, but never had to use it yet. I would try a couple of M4 (or whichever) washers under each blade, and possibly longer countersunk machine screws, either hex or torx drive so the blades can be really solidly locked down. It does not appear there can be much depth of thread in the blocks above the slide shafts, so matching the screw length to the blade height is probably quite important.
    • rjenkinsgb
      2650G "successful" disassembly and reassembly

      By rjenkinsgb · Posted

      Don't the holders have different sizes front & back? I started out with some cheap cast metal ones, but had a lot of trouble with the movements coming loose, so I got a pair of Bergen ones from cousins, a 4039 and a 4040. Those a well made, properly machines and between them they cover from around 10mm up to all the pocket watches I've had so far.  
    • levic900rr
      Seiko 7005-7100 Crystal replacement

      By levic900rr · Posted

      Hi Friends, As you might have seen yesterday I'm on to my second restoration and its a Seiko from the 70's (i'm pretty sure) I need to source a new Crystal but I'm struggling to figure out how to identify what type it is. (I did some forum searching but couldnt come up with anything) I'm pretty sure its mineral glass (and that lines up with what I've read online) the outside is flat, there is a pretty good sized bevel around he outside edge, but the inside is surface is concave. It measures 31mm in diameter, and at its thickest (around the edge) its 2.1mm. I was hoping to hop on Esslinger to order up a replacement but that hasn't worked out. I can't find anything of this style.  Any ideas? Thanks so much. 
    • rjenkinsgb
      Gruen case back removal - snap or screw?

      By rjenkinsgb · Posted

      I'm having difficulty finding an exact match to the spare case & what movement it originally had? The nearest I can find are the Power Glide, with a 560RSS movement and Borgel case - though that model has a deep case back for the automatic works, while my case has a flush back. https://gruen.watch/?product=gruen-geneve-23-precision-power-glide-560rss https://www.birthyearwatches.com/product/c1959-gruen-power-glide-automatic/ The case shape and crown detail are identical to that, and dimensions match except for depth.   The 560 appears to be the same diameter as the 510 and from the same era, so it does seem possible that it's for a less common 510 version? I just have to find an appropriate dial to suit it.  
    • Murks
      Dg2813 chinese clone

      By Murks · Posted

      A have this chinese clone DG2813 movement can a eta 2813 mainspring fit in this movement it doesn't tell you what mainspring to you in this movement are very similar ?
×
×
  • Create New...