Jump to content

avia 15 jewel AS1002

jthing
 Share

Recommended Posts

jthing Member

jthing

Posted
  • Author
Posted
8 minutes ago, RichardHarris123 said:

Your welcome.  I general oiling one movement is the same as oiling other movements, unless it's something special.  Light oil for fast moving parts and heavier oil for slow moving parts. 

thanks again. i have a list that i have used in the past. also been reading info on oil on here to get the latest info..

Link to comment
Share on other sites
Marc Distinguished Member

Marc

Posted
Posted (edited)

AS984 / 1002 is a nice basic sub-seconds time only manual wind movement so about as uncomplicated as it gets. You're highly unlikely to find a service manual for it but all you need to do is to follow a logical system of work, work slowly, don't force anything, and take pictures of every step of the strip down as reference for when you put it back together. Also make sure you let down the power before you start, and it's good practice to remove the balance cock and balance and put it somewhere safe at the start of the works, that way it's less likely to be damaged.

One thing to note (and I have just checked this on a 984 in my parts stash) is that both the crown wheel screw and the ratchet wheel screw are reverse (left hand) threaded, so turn clockwise to undo. Otherwise there should be no real surprises.

I have attached a copy of the BHI guide to lubrication which should be more than adequate for your movement and is a good starting point for most clocks and watches in the absence of anything more specific.

If you get stuck on anything just ask on here.

BTI-The_Practical_Lubrication_of_Clocks_and_Watches.pdf

Edited by Marc
typo, I think I may need new batteries in my keyboard :-)
  • Like 1
Link to comment
Share on other sites
Swan Member

Swan

Posted
Posted

Let me know how you get on! I have (I think) the same movement in a Timor WWW that's next in line on my bench. I think as Marc says, hopefully pretty straighforward. Have you folloed Mark's courses on watchfix.com? I think with the knowledge there, you should be good to go. 

  • Like 1
Link to comment
Share on other sites
jthing Member

jthing

Posted
  • Author
Posted
8 minutes ago, Swan said:

Let me know how you get on! I have (I think) the same movement in a Timor WWW that's next in line on my bench. I think as Marc says, hopefully pretty straighforward. Have you folloed Mark's courses on watchfix.com? I think with the knowledge there, you should be good to go. 

I have watched a quite a few of his videos. Also worked on Seiko auto's. Citizen & walthan. Not done any for a year or two. But when I have time. Would like to do more!

1 hour ago, Marc said:

AS984 / 1002 is a nice basic sub-seconds time only manual wind movement so about as uncomplicated as it gets. You're highly unlikely to find a service manual for it but all you need to do is to follow a logical system of work, work slowly, don't force anything, and take pictures of every step of the strip down as reference for when you put it back together. Also make sure you let down the power before you start, and it's good practice to remove the balance cock and balance and put it somewhere safe at the start of the works, that way it's less likely to be damaged.

One thing to note (and I have just checked this on a 984 in my parts stash) is that both the crown wheel screw and the ratchet wheel screw are reverse (left hand) threaded, so turn clockwise to undo. Otherwise there should be no real surprises.

I have attached a copy of the BHI guide to lubrication which should be more than adequate for your movement and is a good starting point for most clocks and watches in the absence of anything more specific.

If you get stuck on anything just ask on here.

BTI-The_Practical_Lubrication_of_Clocks_and_Watches.pdfUnavailable

Thanks Marc. Very helpful.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Questions about my Bravingtons Renown Mantel Clock

      By Neverenoughwatches · Posted

      Hmmm you know when i said some damp might have caused the bubble originally hmmm 🤨
    • Neverenoughwatches
      404 Club Reboot

      By Neverenoughwatches · Posted

      Are you all jerking my chain, I'm a yorkshireman £4.04 is too much 😆
    • Kkramme
      Blew it with a coil

      By Kkramme · Posted

      [Myota2034] Custom simple quartz watch — PricewaterhouseCoopers On a very very different note, here is a watch from approximately 2000 when I was a Partner with PwC, Management Consulting. It was a simple “marketing watch” with a clever “vase of knowledge” that is subtly revealed on the dial as the second hand progresses. Clever for a simple watch!⌚️
    • Neverenoughwatches
      Mainspring winder question.

      By Neverenoughwatches · Posted

      I think someone else has though. Some where here using a modified perspex sheet. I may be wrong i may be right , i think it involved fitting the arbor to a pin vice. I dont have experience of the bergeon winders, are the handles not interchangeable ?
    • Neverenoughwatches
      Dial Dots

      By Neverenoughwatches · Posted

      Never tried dial dots, i always considered them as a bit of a bodge.  You are adding something that was never intended to be there. I wonder how the adhesive reacts to any part of the movement, hot summer heat and i think things might turn sticky. Most adhesive backed stuff has a tendency to soften and slide around so it may spread, i have used a lot of so called sticks all adhesives in my industry that are just not up to the job. I suppose they get you out of a problem quickly, but how permanently might that be ? I would just explain to the owner that it may or may not work. WWs other ideas are a much more permanent solution but both have their risks . I've tried milling and dial feet replacements, hmm it was ok, ive heard of folk dimpling the face , so that needs care . And i have soldered a few times , all with good results but i am very careful and I practiced it a lot.
×
×
  • Create New...