Jump to content

Extra Fiddly Smiths Empire

rehajm
 Share

Recommended Posts

rehajm Super WRT Addict

rehajm

Posted
Posted

I'm having difficulty trying to case this Smiths Empire. I've managed two others previously but this one is a bit different- a case tube. I'm aware of the Smiths procedure of depressing the stem screw to allow clearance to slide in the stem but the trouble is with this design when the stem is inserted the case presses on the dial and does not allow sufficient clearance to depress the stem screw. Any ideas? Is the case really two pieces? If it is I don't see where the bezel ends...

IMG_1052.jpeg

IMG_1051.jpeg

IMG_1049.jpeg

IMG_1050.jpeg

Link to comment
Share on other sites
rehajm Super WRT Addict

rehajm

Posted
  • Author
Posted
5 hours ago, watchweasol said:

I had one like that and I ended up removing the crown fitting the stem and slotting it into the case minus the crown, then refitted the crown and managed to get enough grip to tighten the crown down with a dab of loctite.   

Thanks- I’ll give that a try!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
×
×
  • Create New...