Jump to content

Extra Fiddly Smiths Empire

rehajm
 Share

Recommended Posts

rehajm Super WRT Addict

rehajm

Posted
Posted

I'm having difficulty trying to case this Smiths Empire. I've managed two others previously but this one is a bit different- a case tube. I'm aware of the Smiths procedure of depressing the stem screw to allow clearance to slide in the stem but the trouble is with this design when the stem is inserted the case presses on the dial and does not allow sufficient clearance to depress the stem screw. Any ideas? Is the case really two pieces? If it is I don't see where the bezel ends...

IMG_1052.jpeg

IMG_1051.jpeg

IMG_1049.jpeg

IMG_1050.jpeg

Link to comment
Share on other sites
rehajm Super WRT Addict

rehajm

Posted
  • Author
Posted
5 hours ago, watchweasol said:

I had one like that and I ended up removing the crown fitting the stem and slotting it into the case minus the crown, then refitted the crown and managed to get enough grip to tighten the crown down with a dab of loctite.   

Thanks- I’ll give that a try!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Introduction

      By RichardHarris123 · Posted

      Hello and welcome from Leeds. 
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
×
×
  • Create New...