Jump to content

Refinishing after rust removal

RedVitus

By RedVitus
in Polishing & Refinishing

 Share

Recommended Posts

RedVitus Member

RedVitus

Posted
Posted (edited)

I worked through this refinishing issue and decided to post my solution for forum readers who may end up in this situation.

During a routine watch service, I noticed a little surface oxidation on a pocket watch spring.  It wasn't a lot, so I tried removing with a glass fiber brush. That removed some of the rust, not all, so I decided to go further.

Then after some light work on a coarse diamond plate, the rust was gone, but it left a reflective, polished looked instead of the dull finish originally that all the other steel parts under the dial had. The two pictures below show how the spring looked after rust removal next to a part (yoke) with finish I was trying to match.  It looked almost passable from one angle but from another (direct on top) not very close.

20220918_160213.thumb.jpg.5662a5df1c3e5f680a4d35f1c2aea10a.jpg20220918_160148.thumb.jpg.34b15e0bfa848074eede71ff07b42a44.jpg

I hadn't come across the situation before. Typically when I refinish steel it is to mirror finish. Never tried to match a dull or grey finish.

First guess was that it would naturally dull over time and I shouldn't bother but after some thought I came to the opposite conclusion. 

I did a test to see if I could dull the metal to at least get something with less luster. Having some experince removing rust from old tools with vinegar, I knew that it changes the appearance- usually darkening steel. 

I decided to try it so placed the part in white vinegar. Perhaps a short soak would dull but not darken the metal? A few minutes  gave the grey that I was looking for. 

The after photo is below. Looks pretty darn close to my eyes.

20220918_161645.thumb.jpg.bd409dd4999789fcd7dec025fe52aa59.jpg

 

Edited by RedVitus
Removed a typing mistake
  • Like 6
  • Thanks 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By JohnR725 · Posted

      I'm a little confused here before servicing everything was fine and now it's not? Then I'm assuming if you run it without the chronograph modular runs just fine or does it give you problems then? Then as far as tightening goes I've occasionally seen people use a staking set and sometimes it works sometimes it doesn't. You can also disassemble and flip it over that sometimes works. Otherwise try eBay and maybe one will come up. There is a tiny possibility if the Problem is on the gear part and not on the center tube that you could purchase a shorter version and pop it on your longer version that's a speculation on my part that may be that might work but if the tube itself is worn then you're going to have a problem then it's back to eBay and just try to find one in the first place all sorts of things will show up on eBay sooner or later.    
    • nickelsilver
      Gruen 330 balance complete

      By nickelsilver · Posted

      Why do you need a whole balance assembly (balance complete)? Staffs are readily available and cheap.
    • watchweasol
      Greetings from Whidbey Island.

      By watchweasol · Posted

      Hi welcome to the forum. Enjoy. dictionary_ebauches_sa.pdf TZIllustratedGlossary.pdf
    • Simeon
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By Simeon · Posted

      Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • caseback
      Chinese tools debate

      By caseback · Posted

      He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
×
×
  • Create New...