Jump to content

Remember, take your time.

Shane
 Share

Recommended Posts

Shane WRT Addict

Shane

Posted
Posted

The watch I was working on when I posted "Do Not Open, Bulova Sealed" is, once again, alive and well. (I still need a gasket for it)

This one tested my patience and I needed to step away at multiple times. Both balance jewels and their clips needed to be dug out of their respective pockets. The hairspring needed to be slowly soaked and delaminated coil by coil. Once the oil was desolved, just about every part needed to be brushed to remove some hardend deposits of polomerized crud.

An arduous two weeks of not knowing exactly when the expletives would start.

At the end I should have stepped away at least one more time. I rushed installing the hands and put the minute hand on several minutes fast. I pulled the hands back off and slipped putting them on the second time, scratching the dial. The scratch (at 10:30) is small and unnoticeable with my naked eyes but is there and will haunt me every time I wear it.

I hope this will help everyone myself including take your time and breathe.

VID_20220428_162954_exported_548.jpg.96c662a33366bb811de84f31bc43bd65.jpg

 

  • Like 4
grsnovi Distinguished Member

grsnovi

Posted
Posted

Good job!

I'm taking my time but not because I want to. I need to score a mainspring winder! Somebody said: "All things come to those who wait..."

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • tonydagee
      Calendar work certina 25-651

      By tonydagee · Posted

      Hello all, just disassembling to service, but I can’t figure out the working of the calendar work…it’s not operational the jumper and spring are ok, but the operation of the driving wheel has me at a loss. I can’t see a cam to drive anything. Is something damaged or missing? Help please!
    • tIB
      Unusual Seiko dial damage

      By tIB · Posted

      Believe the relume (not a fan) was done a long time after the damage. 
    • Malocchio
      Unusual Seiko dial damage

      By Malocchio · Posted

      I can only think of some chemical reaction to reluming
    • nickelsilver
      A lathe with indexing that won't break the bank?

      By nickelsilver · Posted

      I have a little milling attachment for my WW lathe, but very rarely use it and not for wheel and pinion cutting. For that I use a small Sixis 101 milling machine. I normally do direct dividing, but sometimes have to do an odd count and use the universal index which also fits on the Sixis.   Back in the day when I didn't have a mill, I would cut gearing on my Schaublin 102. It has a universal dividing attachment which fits the back of the spindle. Both it and the one for the Sixis are 60:1 ratio, and with the set of 4  index plates I can do almost any division. When I've had to do a strange high count prime number, I print a disc with the needed division and just place the plunger on the dot. Any position error is reduced by a factor of 60 so still plenty accurate.   The machines are a mess in the pics as I'm in the process of making a batch of barrels for a wristwatch 🙃.   This is the Sixis. The head can also be placed vertically, as can the dividing spindle.   Dividing plates. The smaller ones fit another dividing spindle.   Universal divider for the Sixis. I put it together with parts from an odd Sixis spindle that takes w20 collets, like the Schaublin 102, and a dividing attachment from a Schaublin mill.     The dividing attachment for the 102. The gear fits in place of the handwheel at the back of the headstock.   And the little milling attachment for the WW lathe. I just set it on the slide rest to illustrate the size, you can see from the dust on it it really doesn't get used much. I think only when I change bearing in the head, to kiss the collet head seat (grinding wheel still in the milling attachment).
    • SidKop
      Opinions on Seiko's 4R and 6R movement quality from those more able to judge

      By SidKop · Posted

      I read a lot about the quality (or lack thereof) of Seiko's 4R, 6R, 8L  movements...or more specifically the lack of regulation from the factory. Especially when compared to similar priced manufactures using SW200's or ETA's. I thought I'd ask those more in the know, do the 4R's and 6R's deserve their bad reputation, is it fairly easy for someone with minimal skills (or better yet a trained watch mechanic) to dial in these movements to a more acceptable performance.    For background I spent more on a 1861 Speedy years ago, expecting that the advertised 0-15s/d  would probably perform more like 5-7s/d. In reality it's been closed to 2-4s/d. 
×
×
  • Create New...