Jump to content

Making a burnisher

arron
 Share

Recommended Posts

arron WRT Addict

arron

Posted
Posted

Good evening all,

I am trying to make a burnisher in lieu of buying one of the expensive combination pivot file/burnishers i see online.  I bought the $14 hardened steel burnisher at timesavers to work with.  The burnisher is perfectly smooth so i'm assuming i need to finish it.  I found a couple of written sources about finishing the burnisher using sandpaper on a piece of glass.  I can't find however what grit sandpaper i should be using.  one source just said to use coarse grit on one side of the metal and fine grit on the other.  Does anyone know what grits i should use?  My intention in case that matters is to polish/burnish PW wheel and balance staff pivots.  Thank you.

burnisher.jpg

Link to comment
Share on other sites
  • 2 months later...
Michael1962 Distinguished Member

Michael1962

Posted
Posted (edited)

Welcome to the forum Aaron.

Glad someone else has asked as I have the same questions myself. I just have to find someone that carries the material for a burnisher in Australia.

I think I know which material may be suitable, but I have seen several recommendation s so it starts getting confusing.

Edited by Michael1962
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • nevenbekriev
      the escape wheel can't move itself

      By nevenbekriev · Posted

      You need to know at least the basics. Then the questions that You ask will begin to make sense. From what is seen on the video, the gear train and escapement look fine, but the balance doesn't rotate free. I can suppose that the thin gold colored shim that must stay under the balance cock is not in place.
    • nevenbekriev
      Waltham A-11 Hairspring and Balance assessment help needed.

      By nevenbekriev · Posted

      Yes, there are a lot of shapes and all of them are used in different cases. The one in Waltham A11 is one of the most spreaded and is what I have shown in the beginning. Of course, the radius of the final curve will depend on the distance between the hole in the stone and the regulator pins on the cock
    • Michael1962
      404 Club

      By Michael1962 · Posted

      I just found these. They don't really grab my eye at the moment, but having seen the change in some of the watches on here, before & after, the results have been pretty impressive. https://www.ebay.com.au/itm/196382906131?itmmeta=01HXBSJJXDB5J6H916ARJP9PHE&hash=item2db9555713:g:REwAAOSwUNdmOYAZ&itmprp=enc%3AAQAJAAAAwOAlUO3a1pAUX60Y8gUeXMPriraj5e7rkBNH2EA6cIUH7kb7hzoq6jRmOsYOQazk9R%2FteDESr1e50Asabv2tbJyDM%2FVODtmrAScFS4jPhHdgu6Jvt%2BFuRGBijpTkPl4NiK%2FDGr6qztc1Ujb33Tt6YdaUztOH9R1y9XJbwjH0puPDy8m0ilYcal7Vphcp7d59DLtBliNnbqfxfWhxdia2xMRyHYFHzR0Rg7NqB1z4xQGMZb73MAG4QBiF9FMkrII88Q%3D%3D|tkp%3ABk9SR_KuyvnqYw
    • Waggy
      404 Club

      By Waggy · Posted

      I agree, it's getting harder and harder to find anything that meets the brief other than complete junk, or fake/frankenwatches. I would be in favor of raising the limit so people can continue to enjoy the challenge of resurrecting these low cost watches to their former glory and allowing the watchmaker the ability of practicing new skills without the worry of breaking the bank if all doesn't go to plan. Now all we need to do is settle on a value - maybe base the value on a standard currency so we are all playing by the same rules ($, £, €...?) Unless anyone minds I could start a poll and we could all vote on currency and value... let me know!
    • BlueHarp
      Pcket watch "Art déco"?

      By BlueHarp · Posted

      Same for me, but this is the first time I use the Bestfit. I understand that, for a 17-3/4 caliber, I have to consult page 150, but I can't find any resemblance. Thank you for all your research. I learn a little more each time I use this forum 😀
×
×
  • Create New...