Jump to content

Lanco (Langendorf) 1305 Sport de Luxe

Ludo1986NL
 Share

Recommended Posts

Ludo1986NL Member

Ludo1986NL

Posted
Posted

Time to show off one of my longest lasting projects. Learning how to electroplate, filing down the watch case, fully servicing the movement and replacing (after a VERY long search) the clutch cap .

It's still not perfect, the movement 'moves' a bit in the case due to one missing (and replacement not fitting) case clamp + screw, but, I wear it with pride each day. 

Hopefully it inspires some of you to keep trucking when a project looks almost impossible, I started out in January and happy to see I'm making progress. 

IMG_2171.jpg

IMG_2356.jpg

IMG_2370.jpg

2F31597B-554B-4CB9-A2E5-8739AF099A67.JPG

  • Like 4
Link to comment
Share on other sites
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Dmitry
      Eta 2970-1 rotor mount stops watch

      By Dmitry · Posted

      Here are the pics of the bridge. Looks correct, but as soon as I screw on the rotor, the watch stops. Video here: https://1drv.ms/v/s!ArG5E62RGctxjokY5ws85BzuJLVakA  
    • KarlvonKoln
      B-Dip residue?

      By KarlvonKoln · Posted

      One-dip or naphtha should be safe, but are you sure it isn't magnetized?  I would also check that.  Although, if that balance is from an Elgin 760 0r 761, I would think it would have a hairspring of non-magnetic alloy.
    • Curare
      Spell Check

      By Curare · Posted

      Hi, Is there a spell check function available when you are posting ? Regards CJ
    • Curare
      Replacing armoured crystal in a front loading watch case…

      By Curare · Posted

      Hi John I just did a Seiko Lord-Matic a front loader without a split stem, I used a crystal lift to remove it, although I had to have it that tight I though I was going to break the lift before the crystal would budge. So I decided that the press would be a better option as I think crystals with tension rings resist a lot of compressing. I used a crystal press to repalce it and the bezel with no issues, obviuosly a different watch to the Omega. I just took my time and kept inspecting the installation progress bit by bit Regards CJ
    • Zendoc
      Replacing armoured crystal in a front loading watch case…

      By Zendoc · Posted

      Hello All, I’m replacing the crystal in an Omega Dynamic, # 165.039, which houses a cal 552, installed through the front of the case. The replacement Sterncreuz crystal is, like the original, with tension ring. I removed the crystal using a compressed air technique to pop it out.  (I have a crystal lift, but I’m always fearful of marking the crystal edges and so avoid using it as much as possible). Now to the replacement -  any tips on putting the crystal back in?  Am I obliged to using my dreaded crystal lift to complete the task, or how about a crystal press?  I’ve put lots of crystals in using a press, but never with the movement in the watch. The thought of using one with a front-loader makes me very nervous, with the fully assembled watch sitting under the press. How would more experienced folks proceed here? Any advice, gratefully received… John Down Under…
×
×
  • Create New...