Jump to content

Stuck screw

handwound

By handwound
in Watch Repairs Help & Advice

 Share

Recommended Posts

jdrichard Distinguished Member

jdrichard

Posted
Posted
8 minutes ago, handwound said:

Hey guys,

I‘m trying to remove the lower balance end stone of a movement I want to service, but I can’t get the screw that holds it in place to turn. Any advice?

5E694FF6-5A4A-410E-91E7-F6787475904A.thumb.jpeg.2dd73df4d6786f99b54f4c67c16baae4.jpegBF456073-3923-408A-9177-663FD36EEE42.thumb.jpeg.0e0fd5fc719db0a0fcc82ad20799b3f6.jpeg

Is the Screw slot too shallow?  TRy pressing down hard with the screwdriver (make sure you have a grig in the slot) and use a pare of vice grips to turn the screwdriver while applying top pressure on the screwdriver.  Please dont slip.

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
13 minutes ago, handwound said:

that was probably misleading. The blade itself is fixed in the scewdriver and doesn't turn, just as it should. But the tip of the blade gets twisted before the screw starts to turn. 

Can you put some oil on the screw and leave it overnight, then clean off and try again.  Dress your screwdriver so it exactly fits the slot.

Link to comment
Share on other sites
WellAdjusted Member

WellAdjusted

Posted
Posted

These screws are easily stripped, and it was a common problem back in the day. As an aside, Hamilton in its later watches had threads in the cap jewel setting, with the idea that it's easier to deal with a stripped setting vs a stripped main plate.

Anyhow, I'd recommend heating and cooling the piece. The steel screw and brass mainplate will expand and contract at different rates.

If you have a heated ultrasonic, run it as a high temp for around 20 minutes. If that doesn't work, rinse it, freeze it, let it come back to temp, and repeat with a heating cycle.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Bonefixer
      FHF70 balance jewels settings

      By Bonefixer · Posted

      Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      Oh and this almost perfect third wheel pivot and slightly set mainspring  Ah ok yes i see what you mean, good idea. I'll try that if i fluff this one up. The image isn't great quality but i like the idea though.
    • RichardHarris123
      Part swapper to part maker

      By RichardHarris123 · Posted

      Why cut the paper, cut a square around the image and grind to it. 
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      I did try that last time Rich , i traced the image from the Bestfit book which is the actual size. But its more difficut to cut the shape from paper than it is to grind the steel to shape. This way is pretty easy and the final shaping is done when fitting the part. There are a couple of things i will do differently next time, clamping the 2 pieces together with a drill press will help to hold while scribing the shape in. This was a bit tricky having only one hole, if using the pins and cork the drill size needs to match the pin diameter so there is no movement at all from the template. This movement hasn't finished frying me yet, damaged thread in the plate crown wheel hole and two rubbed in cracked jewels, thats gonna be much more fun.
    • Neverenoughwatches
      A big thank you.

      By Neverenoughwatches · Posted

      👍 Whats not to follow OH ?  You're every inch a pro and a true gent, i always enjoy reading your answers even some of the clock stuff that i dont have a clue about. 
×
×
  • Create New...