Jump to content

Open ended watch strap

Davey57

By Davey57
in Watch Repairs Help & Advice

 Share

Recommended Posts

Davey57 WRT Addict

Davey57

Posted
Posted

Hi

I haven’t been around much lately, but still trying to fit in a bit of meddling when I can. I have just resurrected my grandfathers old watch, it had a broken balance which I replaced with a secondhand one. At some point in time it had also had a new stem fitted, not very welll if I may say so. It was too long and the crown was too thick, it looked awful. So after a stripdown and clean it is running nicely, I have found a nicer crown and trimmed the stem. It is a lovely old watch. My grandfather died about 40 years ago and it has not run in all that time, I’m not sure when the balance was broken. All I need now to finish it off is a new strap. The case has fixed pins so I need an open ended strap. I have searched for 17mm open ended straps but can’t find much. The only likely contender was a Hirsch, nice straps but quite expensive. Does anyone know where I might find something? Maybe it does deserve a nice Hirsch strap to finish it off. I need a shortish strap as I have slim wrists, the one fitted is ideal length at around 75/110. Thanks in advance for any suggestions.5884A28E-E8BE-4F9C-8A87-1A3F47F25E52.thumb.jpeg.65b0adf4b7e7d28eb9839a4f97fc330e.jpeg

AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

Have you considered simply re-stitching the existing one. It has a certain veteran charm of its own.

Its not a particularly difficult job. You just need a couple of needles, some suitable waxed thread, and a little patience.

Start by removing the existing thread, then remove the fold over metal tabs, clean those and check for damage, if necessary cut replacements from thin brass sheet.

Clean the leather, use ordinary soap and water for this, then nourish it with the leather treatment of your choice (beeswax based, rather than silicone, I would say, just to keep with the vintage spirit).

Replace any internal cotton or other damaged or worn out spacer material, sew it back to together neatly.

More about the technique can be found in a number of videos on youtube.

Here for example.
 

 

Those Hirsch ones do look good though. Maybe get one for "Sunday best" for it too.

Edited by AndyHull
  • Like 1
AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

There are some less expensive options on the bay of course. For example -> https://www.ebay.co.uk/itm/Vintage-Genuine-Leather-Black-Open-Ended-Watch-Strap-NOS-Fixed-Lugs-16mm-17mm/222901723491?hash=item33e5fa6163:m:mWmXuxs5-03_WbpfqOhyfJA
(That ones looks like it genuinely is  new old stock.)

Try searching for some variations of "Genuine Leather  Open Ended Watch Strap Fixed Lugs 17mm"

Edited by AndyHull
Davey57 WRT Addict

Davey57

Posted
  • Author
Posted

I would love to keep the old strap to use but it wasn’t the correct width, shame. I’ve tried looking for Hirsch ladies straps hoping they might be shorter but no luck.

 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • AndyGSi
      Reusing mainsprings in an automatic and slipping

      By AndyGSi · Posted

      The idler gear I'm referring too is the one between the 2 barrel wheels. These movements just rely on the spring slipping to prevent over winding.
    • EtherJunky
      Tip and tricks here.

      By EtherJunky · Posted

      Not sure how useful this might be, but a while back I bought some bamboo tweezers (multipack with a ridiculous amount of them in) and have been using them in place of pegwood. Seems to be working just fine
    • JohnL
      Reusing mainsprings in an automatic and slipping

      By JohnL · Posted

      Ah, well there is the rub. I ordered a post and oscillating weight, but clicked on the wrong thing when adding the weight to the basket adding an automatic bridge. Ordered a weight, and it's somewhere in the ether after our customs and excise folks rejected it because of the documentation.  Yes, both springs inserted the same. "Is the idler gear ok", and here's why I posted to the newbie area: So, reading between the lines, and again correct me if I'm wrong here, the automatic winding mechanism will have an ideler gear, along with the reverse wheels, that prevents over-winding? There is nothing (that I'm aware of) between the crown pinion, crown wheel, and the ratchet wheels to prevent over-winding other than the mainsprings slipping in the barrels.  This is only the second automatic I've worked on. The other, a Vostok, had a very obvious mechanism.  I shall look at the automatic winding mechanism in a bit more detail when I've a bit more time. At the moment I'm taking a glance here now and then when work is dragging 😉 As ever, thank you for your help. Always appreciated.  
    • AndyGSi
      Reusing mainsprings in an automatic and slipping

      By AndyGSi · Posted

      If the weight was worn how does the post look as normally you'd have to replace both. There should be no real resistance at the end and just be able to keep on winding. Did you insert both springs the same and is the idler gear OK.
    • JohnL
      Reusing mainsprings in an automatic and slipping

      By JohnL · Posted

      Assembled and running well, I'm asking after the fact. I'm waiting on a new oscillating weight as this one was worn (they have a reputation for it apparently, no bearings). So I've been winding it by hand, but meeting quite a bit of resistance at the end, more than I think an automatic weight will overcome. It's not quite as sudden as a manual mechanism, but there's very little in it, certainly enough that I would be concerned about breaking something if I continued.
×
×
  • Create New...