Jump to content

Help With A Loose Vintage Minute Hand.

chrisbuxton27
 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

A controlled nip is required. For this reason I put them in a lathe collet and GENTLY tighten. It is really,really easy to go to far. You can use a broach but I recommend you put the broach in a vice so you have total control. 

Link to comment
Share on other sites
chrisbuxton27 Watch Enthusiast

chrisbuxton27

Posted
  • Author
Posted

Clockboy the type of minute hand I mean has no stem just a flat hand with a hole to push onto the minute wheel. So there is nothing to place in the lathe collet. I'm thinking a stake of some shape to to close the gap slightly but not sure which would do it. Maybe a stake used for setting jewel stones would do it but that's something I've not tried either.

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

Ok sorry did not read the post correctly. However I recommend to get hold of the Cousins catalogue and browse it.

There are lots of hands available , different styles etc.  You will need to know length,width hole size etc. Too small is Ok because you can broach the hole out to fit but to big I really don,t know a way around it. Using a staking set punch might be to much for a delicate hand. The cleaver boys (not me) would make another arbour with a fatter shaft or thin the minute arbour and put a sleeve on. But you need a watchmakers lathe and lots of skill which I do not possess.

Link to comment
Share on other sites
Charlie WRT Addict

Charlie

Posted
Posted

On a proper staking set you will find several hole reducing punches. The five blued punches with round polished ends are the ones I use to re-size hands. Smaller seconds hands as found on sub-seconds dials with tiny tubes I do with my set of pin vises. There are also other ways to accomplish this task, but I find these punches work well for me. I will post a photo shortly.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • AlanB
      Gilding after silver soldering

      By AlanB · Posted

      When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • Neverenoughwatches
      Can anyone identify what this is? Part Two

      By Neverenoughwatches · Posted

      The first one is an Unruh max stake for pushing out staffs
    • JonC
      Can anyone identify what this is? Part Two

      By JonC · Posted

      Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • Zedster
      Roamer Searock Crystal problem

      By Zedster · Posted

      According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
    • JonC
      Dial feet removal

      By JonC · Posted

      When building a new Watch I have tended to use a file to remove the remnants of dial feet that are not needed as many dials come with four feet to accomodate different movements, but this can be a bit messy so now I use this with a great deal more precision as you can use an appropriate bit for the job and keep it very localised.      
×
×
  • Create New...