Jump to content

Identification assistance required please


Recommended Posts

Hi

I inherited some belongings from a relative quite some time ago which included a watch. I'd actually forgotten all about it until a recent spring clean of the attic but with my newfound watch hobby would like to see if I could get this going again.

I have done as much research as I can before  posting here and David at vintagewatchstraps.com has already been extremely helpful in dating a hallmark on the case back Pic3.thumb.jpg.6fc7e02a2b4491d3ee12da76351d7f70.jpgto 1926/27.

The movement has 'AS' on it so that presumably must mean an A.Schild and it is a 10.5''' size. I have not however been able to locate a movement ID and even on ranfft most AS movements are based around the AS 340 type bridge layout. The closest I could find in layout was the FHF 1146. Have dismantled the movement I can confirm there are no additional markings on the underside of bridges etc.

There is also no identification of any sort on the dial front but interestingly there are some markings on the dial back with a stamped '32 34' and what looks like 'VERSZ-HURST' (?). There are various other scratched markings. The case back, as well as the hallmarks which David helped with, has a number stamp of '328174'.

As a 'family heirloom' I'd be very grateful for any information anyone might have that could help fill in the blanks.

Pic0.JPG

Pic1.JPG

Pic2.JPG

Link to comment
Share on other sites

Thank you both for your replies.

Danh - a good observation; thank you. I'd also become preoccupied with trying to find an AS with the same bridge layout as the one I have!

I suspect I've come to a dead-end on additional information but at least I now have an A Schild movement in a watch belonging to a distant relative that was made circa 1926.

And I've found it's not 'VERSZ-HURST' but in fact 'L MEROZ-HURST' on the back of the dial who were based at rue du Temple-Allemand in La Chaux-de-Fonds and specialised in making dials.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • As Richard said, this is a really old school trick for joinery.  Cut i strip of paper, might need to be watch paper  around 1 " x 1/2" lay it over a staking block then press the stud screw into and through the edge of the paper upto the head of the screw. You probably wont even need to pull the paper away the head will pull itself through.
    • Thanks Jon, my mum is getting there day by day, so strong and determined, they dont make em like this anymore 🙂 Old folk are so amazing,  my mum used to love her golf, she didn't stop playing until she was 70 . Enjoy your trip and your golf.
    • Hello,  i am looking to source a winding stem (winding arbor) for a waltham 6/0 d movement. I have found some that claim to fit 6/0, 6/0s, 6/0b etc and somealso claim they will also fit the d as well. The d does have hacking which is driven by the stem seating completely. Given some of the costs of these, i was hoping someone would know of any interchangeability with a source, or know a source where a confirmed 6/0 d stem can be had. I am in the US so a US dealer is best.    thanks in advance. 
    • So great to see and hear- your mum looks great! …my mil had a stroke last summer in the golf course parking lot. I’m flying out tomorrow to visit and play golf. she’s ornery because she can’t get off the tee but I hear she makes up for it on the greens since she’s been putting since a week after her stroke 🧐…
    • Very best wishes to you and your family, as a carer myself I know how difficult things can be.
×
×
  • Create New...