Jump to content

Gear Train Recoil

omgiv

By omgiv
in Watch Repairs Help & Advice

 Share

Recommended Posts

omgiv WRT Addict

omgiv

Posted
Posted

Hi Guys,

 

I'm back with another question that has always been on my mind and am hoping to put it to rest.  I have read on the internet (which doesn't always make it true) that having a little recoil of the gear train when slightly turning the crown (without the pallet for or balance installed) is a good sign of clean pivots and a free train.  By recoil, I mean that you can see the escape wheel spin in the opposite direction at the very end as the mainspring draws back in.  My question is if this is the truth.  I have some watches that will do it and some that won't but all perform well.  Thanks and let me know if I am not being clear in my question.   

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

This is not something that I have heard mentioned before, but I certainly have witnessed the effect that you describe when working on movements. Thinking about it logically as an engineer, I would have to agree with the said theory. I can well imagine that dirt or dry pinions would definitely have a retarding effect and prevent any rebound of the gear train occurring.

Just my tuppence worth!

Link to comment
Share on other sites
autowind Distinguished Member

autowind

Posted
Posted

From what I have read and from experience I would say it essential that the train reverses a small amount after putting a turn or two on the mainspring.  It is a very good indication that the wheel train is running freely,  any power losses in the train are robbing the balance wheel of max. power.  I would even say that if you do not get a reversal,  find out why!

  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

From what I have read and from experience I would say it essential that the train reverses a small amount after putting a turn or two on the mainspring.  It is a very good indication that the wheel train is running freely,  any power losses in the train are robbing the balance wheel of max. power.  I would even say that if you do not get a reversal,  find out why!

 

This is true, except the watches with a seconds pinion held under tension with a spring - those will not recoil.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Questions about my Bravingtons Renown Mantel Clock

      By Neverenoughwatches · Posted

      Hmmm you know when i said some damp might have caused the bubble originally hmmm 🤨
    • Neverenoughwatches
      404 Club Reboot

      By Neverenoughwatches · Posted

      Are you all jerking my chain, I'm a yorkshireman £4.04 is too much 😆
    • Kkramme
      Blew it with a coil

      By Kkramme · Posted

      [Myota2034] Custom simple quartz watch — PricewaterhouseCoopers On a very very different note, here is a watch from approximately 2000 when I was a Partner with PwC, Management Consulting. It was a simple “marketing watch” with a clever “vase of knowledge” that is subtly revealed on the dial as the second hand progresses. Clever for a simple watch!⌚️
    • Neverenoughwatches
      Mainspring winder question.

      By Neverenoughwatches · Posted

      I think someone else has though. Some where here using a modified perspex sheet. I may be wrong i may be right , i think it involved fitting the arbor to a pin vice. I dont have experience of the bergeon winders, are the handles not interchangeable ?
    • Neverenoughwatches
      Dial Dots

      By Neverenoughwatches · Posted

      Never tried dial dots, i always considered them as a bit of a bodge.  You are adding something that was never intended to be there. I wonder how the adhesive reacts to any part of the movement, hot summer heat and i think things might turn sticky. Most adhesive backed stuff has a tendency to soften and slide around so it may spread, i have used a lot of so called sticks all adhesives in my industry that are just not up to the job. I suppose they get you out of a problem quickly, but how permanently might that be ? I would just explain to the owner that it may or may not work. WWs other ideas are a much more permanent solution but both have their risks . I've tried milling and dial feet replacements, hmm it was ok, ive heard of folk dimpling the face , so that needs care . And i have soldered a few times , all with good results but i am very careful and I practiced it a lot.
×
×
  • Create New...