Jump to content

Hamilton Khaki Mechanical / H-50 winding issues

Kalscheid
 Share

Recommended Posts

Kalscheid New Member

Kalscheid

Posted
Posted

Hey guys. I'm currently having trouble with my handwound Hamilton Khaki Mechanical with the H-50 movement. I usually give it a full wind when I take it out of the box (which if I remember correctly was around 45 winds)
Then I would rewind it in the morning which usually took 12-15 winds. When I feel resistance I stop winding - that's what my watchmaker told me and what I read and hear online all the time.

Well, all of a sudden my watch doesn't reach that point of resistance anymore! I can keep winding as if it was an automatic movement. The watch is still running pretty well at -10s/d

Now, without having opened it I wonder what could be the problem here. I have a hunch that my son might have taken the watch and overwound it while I was not looking but in that case - how is the watch still running?


Thanks in advance for your thoughts. I'm fairly new to the watch repair hobby and I'm not sure I want to try my hands on this watch – I'm still not done butchering my first project…  

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

Welcome to the forum, enjoy.. Normally if a hand wound watch does not fully wind ie just keeps winding there is an error with mainspring, either slipping around its winding arbour or the mainspring is broken. 

  • Like 1
Link to comment
Share on other sites
nevenbekriev WRT Addict

nevenbekriev

Posted
Posted

Hi and welcome.

First of all, check the power reserve. If the watch is runing, this means the spring is attached to the barrel arbor. If there is no end of winding, this probably means that the spring is not attached to the barreland it's outer end is slipping. In such case, the watch will run, but the power reserve will be small - about several hours

  • Like 1
Link to comment
Share on other sites
Kalscheid New Member

Kalscheid

Posted
  • Author
Posted

Thanks for your feedback guys.

I gave the watch (what I consider to be) a full wind and will check the power reserve. I think the last time I tried, it ran for at least 48 hours so this will take a while. As the watch IS running I think the arbor IS attached to the main spring. I was suspecting that maybe the main spring is slipping inside the barrel much like it would in an automatic watch. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Simeon
      Bezel replacement difficulty

      By Simeon · Posted

      The bezel feels slightly loose over the case. There wasn't a gasket but could the crystal be expanded over the lip in the caseback and then the bezel pressed over the crystal?  Actually this sounds like a possibility. This is a great forum. https://www.watchrepairtalk.com/topic/20587-old-orient-case/?do=findComment&comment=173918
    • rjenkinsgb
      Black coating on shock jewel metal housing

      By rjenkinsgb · Posted

      The cleaner smells of ammonia, but it's not too bad; just keep it covered as far as practical.  I use an ultrasonic machine on a kitchen worktop. The rinse does not smell strongly, it's vaguely like paraffin. I did check the safety data sheets before buying it & it's said to be safe in normal use. My dedicated watch cleaning machine is still a work-in-progress; four position linear, based on 1L kilner jars for station spacing, to have a heated dryer in position 4. It uses standard, readily available parts as far as possible to make it easy to reproduce, plus 3D printed bits for the custom parts. (The horizontal drive motor is out at the moment while working on the stepper drive software)    
    • Albyon
      Citizen Pilot Radio Controlled hour's hand clearance

      By Albyon · Posted

      I disassembled the hands of my Citizen Pilot Super Titanium Radio Controlled AS2031-57E a couple of times.  The second time because on the first attempt i evidently did not push the hour hand well and in practice it was not well fixed and moved receiving even small bumps. After the second attempt everything seems to be ok.  Except that i have the impression that giving a little more sustained blows on the wrist, the hour hand still has a slight movement, in the order of half a second or less. It is a normal, topical and usual thing about this movement, which, i remind you, is exclusively electronically managed, each hand independently, a clearance in the movement that it has of its nature, or it may depend on the hand is not yet well attached to the pin and should perhaps be replaced because the hole has slightly enlarged?
    • Neverenoughwatches
      Balance staff sourcing?

      By Neverenoughwatches · Posted

      This is something a lot of beginners and amateurs struggle with Nev, being able to remove the staff without distorting the hole of a non steel balance wheel. Having the right tools to do this safely  and effectively is not easy. Even with something useful it takes a lot of practice, i spent two days not so long ago practicing cutting away the balance wheel hub of a staff using a 25mm diamond wheel.  I didnt manage to do it once without catching the underside of the wheel.
    • Malocchio
      hidden lug watch

      By Malocchio · Posted

      Then you should have something that prevents the case from moving. I just bought one of these Seiko S-210 but haven't received it yet.
×
×
  • Create New...