Jump to content

I need to find a case for my movement.

woody24
 Share

Recommended Posts

woody24 New Member

woody24

Posted
Posted

Hello! Finally digging into my first repair. Watched Lessons 1-3 on WatchFix, so now I'm an expert! Ha. But there's one question that I haven't seen answered in these classes, or in other Youtube videos. How do you find the proper case for a watch?

I bought a cheap movement on ebay. Something that says it didn't run/for parts. I got it going, and now I'd like to actually wear it. It didn't come with a case. It did come with a really nicely worn dial. But I'm struggling on how to find the proper case for it. 

The movement is just a hair over 23mm. And the dial is just slightly over 25mm. It's just a standard manual watch, with the seconds hand down by the 6. What do I need to look for, or search for when looking for a case? I see people showing the dimensions of the outside of the case, but I don't see how that'll help me. I'd hate to buy a complete watch of the same caliber. And since there seems to be a lot of these movements on ebay without cases, the cases have to be somewhere, right?

I've seen plenty of complete watches with square faces. But this movement came with a round dial, so I'd like to find a round dial case. 

Also, if you end up sending me a link to a case that would work, would you mind "showing your work" on how you found that? 

Thanks! Enjoying this so far. Blow away by how small these things are. How the heck did they make these things to begin with? Ha.

Link to comment
Share on other sites
Kalanag Super WRT Addict

Kalanag

Posted
Posted

Nothing is standardized in watchmaking. So each combination of movement and dial requires its own case in terms of dimensions. You have to be more than lucky to find a matching case for your movement and dial.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

I don't know if suppliers still do this, because I have been retired for years. All you needed was the cal number of the movement say if you wanted white metal or gold plated and give as much info as you could such as description of the dial, seconds hand center or other and they would send a case that would fit. 

Link to comment
Share on other sites
woody24 New Member

woody24

Posted
  • Author
Posted
8 hours ago, Kalanag said:

Nothing is standardized in watchmaking. So each combination of movement and dial requires its own case in terms of dimensions. You have to be more than lucky to find a matching case for your movement and dial.

 

Makes sense. I was hoping that since movement's pretty much follow a similar layout, was hoping fitting cases was similar too. Haven't really seen anyone explain how cases work, other than a brief mention in videos as they are taken them apart. 

Besides eBay, are there any other sites that are good for buying used watch parts? 

Link to comment
Share on other sites
spectre6000 Distinguished Member

spectre6000

Posted
Posted
12 hours ago, oldhippy said:

I don't know if suppliers still do this, because I have been retired for years. All you needed was the cal number of the movement say if you wanted white metal or gold plated and give as much info as you could such as description of the dial, seconds hand center or other and they would send a case that would fit. 

Which suppliers would have done this? I've not heard of this before.

Link to comment
Share on other sites
nevenbekriev WRT Addict

nevenbekriev

Posted
Posted (edited)
On 1/7/2024 at 6:38 AM, woody24 said:

...And since there seems to be a lot of these movements on ebay without cases, the cases have to be somewhere, right?
 

Sorry to ruin You idea how the world works...

Some of the cases get worn and good for nothing, and gold plated ones go to the acid and only the golden 'skin' is what lefts... That is what modern gold diggers do.  There is plenty of naked movements but no cases for them at all.

Edited by nevenbekriev
Link to comment
Share on other sites
woody24 New Member

woody24

Posted
  • Author
Posted
14 minutes ago, nevenbekriev said:

Sorry to ruin You idea how the world works...

Some of the cases get worn and good for nothing, and gold plated ones go to the acid and only the golden 'skin' is what lefts... That is what modern gold diggers do.  There is plenty of naked movements but no cases for them at all.

That's perfectly fine. I just wasn't expecting it to be a near-impossible task. I was assuming that even if the originals are gone, I'd be able to buy a new case. I wasn't sure how cases work. I figured there may have been a handful of different ways they mount in, but as long as you have dimensions, you could find one. Like crystals and mainsprings. 

It's no real loss. Bought this movement just to see if I could get it running. It's a Longines 23z movement. Figured since it came with the dial, would be fun to make a fully functional watch. 

Link to comment
Share on other sites
nevenbekriev WRT Addict

nevenbekriev

Posted
Posted

Well, there is plenty of cases for Seiko movements that people use to assemble their own custom watches. You can use such case, but will have to make custom spacer ring and all the things needed to 'mary' the movement with the case, which is not so somple task

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
On 1/7/2024 at 4:38 AM, woody24 said:

And since there seems to be a lot of these movements on ebay without cases, the cases have to be somewhere, right?

Sold for scrap in hard times, melted down to make jewellery maybe even into another watch case at some point ?

56 minutes ago, woody24 said:

That's perfectly fine. I just wasn't expecting it to be a near-impossible task. I was assuming that even if the originals are gone, I'd be able to buy a new case. I wasn't sure how cases work. I figured there may have been a handful of different ways they mount in, but as long as you have dimensions, you could find one. Like crystals and mainsprings. 

It's no real loss. Bought this movement just to see if I could get it running. It's a Longines 23z movement. Figured since it came with the dial, would be fun to make a fully functional watch. 

Its more than just inside diameter and height sizes,  lip to support the dial dimensions, spacer ring around the movement to keep it stable, stem hole position, tube size. Sounds like fun.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Questions about my Bravingtons Renown Mantel Clock

      By Neverenoughwatches · Posted

      Hmmm you know when i said some damp might have caused the bubble originally hmmm.
    • Neverenoughwatches
      404 Club Reboot

      By Neverenoughwatches · Posted

      Are you all jerking my chain, I'm a yorkshireman £4.04 is too much 😆
    • Kkramme
      Blew it with a coil

      By Kkramme · Posted

      [Myota2034] Custom simple quartz watch — PricewaterhouseCoopers On a very very different note, here is a watch from approximately 2000 when I was a Partner with PwC, Management Consulting. It was a simple “marketing watch” with a clever “vase of knowledge” that is subtly revealed on the dial as the second hand progresses. Clever for a simple watch!⌚️
    • Neverenoughwatches
      Mainspring winder question.

      By Neverenoughwatches · Posted

      I think someone else has though. Some where here using a modified perspex sheet. I may be wrong i may be right , i think it involved fitting the arbor to a pin vice. I dont have experience of the bergeon winders, are the handles not interchangeable ?
    • Neverenoughwatches
      Dial Dots

      By Neverenoughwatches · Posted

      Never tried dial dots, i always considered them as a bit of a bodge.  You are adding something that was never intended to be there. I wonder how the adhesive reacts to any part of the movement, hot summer heat and i think things might turn sticky. Most adhesive backed stuff has a tendency to soften and slide around so it may spread, i have used a lot of so called sticks all adhesives in my industry that are just not up to the job. I suppose they get you out of a problem quickly, but how permanently might that be ? I would just explain to the owner that it may or may not work. WWs other ideas are a much more permanent solution but both have their risks . I've tried milling and dial feet replacements, hmm it was ok, ive heard of folk dimpling the face , so that needs care . And i have soldered a few times , all with good results but i am very careful and I practiced it a lot.
×
×
  • Create New...