Jump to content

jumbo doxa crystal replacement

sanadron
 Share

Recommended Posts

sanadron New Member

sanadron

Posted
Posted

This is my first post here. I have been trying to find the right crystal for a 1950s jumbo doxa sa with eta 1147. It is acrylic, 34mm, very thin, and domed to make room for the dial and hands. The old one is cracked and snapped in. I believe it should have been glued but not sure. The shape is similar to the one below.

Any help would be appreciated.

image.png.3fed50231b0970c154d960e5bd1f270a.png

 

Shawn

s-l1600 (4).jpg

Link to comment
Share on other sites
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      My first Gruens. Precision 510 and N510R movements.

      By ManSkirtBrew · Posted

      Just missed it! I have a donor movement on its way. But thank you for the offer--I'll let you know if I need anything else.
    • Razz
      404 Club

      By Razz · Posted

      My latest. Timex 2465. Replaced the crystal, caseback gasket and spring bars. All in less than $5US. Added a gray NATO strap I already had in stock.
    • GuyMontag
      My first Gruens. Precision 510 and N510R movements.

      By GuyMontag · Posted

      I have some Gruen 510's in my donor pile if you need parts.
    • Randy55
      DIY Cleaning Machine

      By Randy55 · Posted

      I've been intrigued by everyone's input here...so I decided to give this a shot. I bought the"typical" Pearl watch-machine basket and trays, for about $65. The trays are good,..the housing is a nightmare ! Thought it would take the mixer off my bench at anything above about 200rpm. The housing is cast of course,..and it's not "true" at all...so the harmonic vibration was insane. So,..I bit the bullet and bought the Elma housing and top. Not the baskets though, as the Pearl one's fit the Elma. Saved a bunch there. The basket and lid came to about $80 with shipping. The opening in the Elma top is 8mm, and the shaft that came with my stirrer is 6mm. I bought a piece of steel tube, 8mm O.D., and 6mm I.D. Cut off about an inch of the tube, and drove the rod into it. Gives a really snug fit.... Lightly champfered the leading edge of the 8mm section, then lightly tapped it into the top of the Elma lid. Spins like a dream now So... I have about $240 total into this including jars and steel mesh for the wave breakers   I'm pretty happy Best to you all   Randy
    • ManSkirtBrew
      My first Gruens. Precision 510 and N510R movements.

      By ManSkirtBrew · Posted

      Still haven't gotten around to getting stems or screws, but I did make my first attempt at polishing a case. I just used a soft mop and rouge to reduce my odds of ruining them, and I think they came up pretty nice. Also gave the crystals a polish on the same wheel while I was at it. They were both very badly scratched up. The one on the left is fairly beat up, but it'll still make for a decent presentation.
×
×
  • Create New...