Jump to content

Brand new vise broke

LittleWatchShop
 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

I bought one of these in Jan.  Set it up for single-purpose use, so I bought another for general use.

Yesterday the knob just broke off while tightening.  Hardly any torque--just shattered.  I have contacted the company.  Will update if I hear back. 

In the mean time, I printed a substitute knob.

image.thumb.png.2a8132dc67d6c913220ef03d73fcda49.pngimage.thumb.png.56d8a3f659b728cf5bd9a33e00458229.pngimage.png.9a565e4c46e3ca1f4e6f395591af486d.png

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Almost ready

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • tIB
      Seiko 6105 crown gasket service

      By tIB · Posted

      Thanks for the info - I'll go big on the gaskets... Wonder if anyone sells hundred packs?!
    • steve1811uk
      Rolex 3135 rate variation with temperature

      By steve1811uk · Posted

      Looked into this some more and I believe that some of the increase in rate is attributable to the drop in amplitude after 12 hours off wrist, from 300 to 275 degrees horizontal and some is due to the lower temperature (38 to 18 degrees). I can see that approx 3 to 4 seconds a day is attributable to each. I can be happy with that.
    • Nucejoe
      Removing the hairspring from a ETA 2846 balance

      By Nucejoe · Posted

      Link below shows the tool used to push the stud out. You can make the tool , just file a screwdriver to this shape.  https://www.esslinger.com/bergeon-16918-etachron-stud-remover-screwdriver/ There are vids on YouTube showing how the stud is to be  push out. Shouldn't get over creative, just go by this approach.  Good luck.
    • Embezelled
      Almost ready

      By Embezelled · Posted

      Hi all, I'm almost ready to make my first attempt at watch repair. My initial goals are very modest, just to get an inexpensive watch or two to work on, and take it at my own pace. I have what I think are the necessary tools on the way. A couple of things arrived already: a loupe, some tweezers, and a cheap demagnetizer. After looking at the options for oils and grease, I decided to start off with Citizen A-O2 and A-O3 oil, and Seiko S-3 grease. The Moebius was just too pricey to buy this early into the undertaking, when added to the cost of the other tools I've bought. Screwdrivers are Kwong Yuen for now, but I took the frequent advice on tweezers and bought Dumostar 3C and will probably add more DuMont later. I'm looking forward to making a start. I'll need a watch to work on, so I'm trying to line up an auction purchase within the next week. I've been mostly looking at Seiko and Citizen, and will perhaps a Seiko Crown if I can land one at a decent price. 
×
×
  • Create New...