Jump to content

Advice Please

Cheaptrick
 Share

Recommended Posts

Cheaptrick Member

Cheaptrick

Posted
Posted

Need so advice on where I may find case and dial for this movement please?

 

Was a cheap eBay win and I reckon Asian in make but that's about all I can guess at,I know case will need push button top right but just wondering if anyone has anymore insight

 

Thanks

post-1079-0-52013000-1432481587_thumb.jp

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I think you may well have a lot if difficulty finding a aces and dial to match that movement. You may well end up using it to hone your repair skills on.

I do hope you find what you are after.

Link to comment
Share on other sites
djqsrv Member

djqsrv

Posted
Posted

That looks very much like a movement I pulled out of a Chinese made Breitling knock off I took apart some time back. It was one of the first watches I took apart and messed with. I remember it had an identical balance bridge. Not sure if that helps you though. :(

Link to comment
Share on other sites
MUTE New Member

MUTE

Posted
Posted

Dear Friend,

 

This can be a problem, however in your case I'd suspect you've got a reasonable problem. If you take measurements on such a movement it may give away an ETA or other common movement of which it closely approximates or matches excactly. If you made me guess I'd bet it matches the dimensions of a Valjoux 7750 family; if so you're in great shape.

 

Once you've done that I'd take a look at the following two places:

 

Very nice Ebay seller with Swiss sourced parts including cases with pushbuttons: http://www.ebay.com/usr/b_line55cc

Frei, especially helpful if you call them and speak with the parts people: http://www.ofrei.com/page460.html

 

As for the dial, looking at where i'd guess the dial feet should sit it might not be hard to find a sterile dial that fits. Strip it in acetone and mill (or even drill...) a date window and a large semicircular cutout for the pretty portion at the bottom.  A little paint, a pad print and you might have a real beauty of a watch that's all yours. Even if you can't print there is a lot to be said for a clean dial on such a watch, especially given the horizontal symmetry between the date and movement portions.

 

As for hands, I'll betcha a beer they're 150/90/20. If that's the case pick whatever you like. If not take measurements and see if anything here:http://www.ofrei.com/page483.html looks good to you.

 

I wish you all the best, let me know how it turns out.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Welcome to the forum Mute, and thank you for a very helpful and informative first post.

It would be good to hear what your own background and interests in horology are. I look forward to more from you in the future. :)

Link to comment
Share on other sites
MUTE New Member

MUTE

Posted
Posted

Welcome to the forum Mute, and thank you for a very helpful and informative first post.

It would be good to hear what your own background and interests in horology are. I look forward to more from you in the future. :)

 

Dear Geo,

 

Thank you for your kind words. It is impressive how helpful and just plain nice everyone here is.

 

Horologically I am a true amateur. I work on my own watches and occasionally put together a unique watch as a gift or thank-you. I owe any knowledge I have to this forum and Youtube videos. I do have some experience with precision small parts manufacturing/prototyping from prior ventures and I hope that can be useful to share with the users of this forum.

 

Again, thank you all for sharing your craft. It is truly appreciated.

  • Like 2
Link to comment
Share on other sites
  • 2 weeks later...
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      hmmmm.... maybe there is a way to skin that cat 🙀 let me think on it... unless anyone else has any ideas? I left the opening in the side of the base and ring quite large to maybe allow you to grip the crown, but appreciate this may not always be possible, especially for small movements where the crown will not extend past the outer wall of the holder. I noticed this also, but after using the holder for a while I noticed that the ring/holder began to wear into shape (rough edges/bumps worn off) and the size became closer to the desired movement OD. Maybe with some trial and error we could add 0.5 mm (??) to the movement OD to allow for this initial bedding-in?
    • Mallard
      Vintage pocket watches from e-bay (winding stems needed)

      By Mallard · Posted

      Hi nickelsilver, thanks for the great explanation and the links! I'll take a good look in the article.  Especially this is great news to hear! Looking through forums and youtube videos I was informed to 'fist find a case and then fit a movement for it'. But seems that's not the case for pocket watches at least?  I guess I should be looking to find some 'male square bench keys' for now. I was thinking of winding the mainspring using a screwdriver directly, but I found a thread that you've replied on, saying that it could damage the spring. 
    • Waggy
      2813

      By Waggy · Posted

      Murks, The rate and amplitude look OK, and the amplitude should improve once the oils you have used get a chance to move bed-in, also I notice that you are using default 52 degrees for the lift angle, if you get the real lift angle (assuming it's not actually 52) this will change your amplitude - maybe higher, maybe lower. I notice that the beat error is a little high, but not crazy high. At the risk of upsetting the purists, if the balance has an adjustment arm I would go ahead and try and get this <0.3 ms, but if it does not have an adjustable arm then I would probably leave well alone. Just my opinion.
    • Murks
      2813

      By Murks · Posted

      Hi everyone on my timegrapher it showing this do a make anymore adjustment someone let me know ?    
    • Waggy
      Epilame / Fixodrop

      By Waggy · Posted

      Maybe I'm over simplifying this and I'm a little late to the discussion, but just by my looking at oil when I use it on a treated cap jewel  the oil stays in one nice bubble, but when I don't it spreads out to the edges of the jewel. I'm not sure (but could well be wrong) but the analogy of a waxed car and rain is accurate in this case, the wax is very hydrophobic and repels the water, however, the process epilame works by is a different physical process based upon cohesion/adhesion (oleophilic) not repulsion (oleophobic)  at least as far as I have read/observed. If one were to use a oleophobic substance equivalent to wax (hydrophobic) then one would need to create a donut shape to fence in the oil, however if one used such a strategy with a epilame which is oleophilic then the oil would sit on the ring of the donut and not in the 'donut hole', exactly where you don't want it. Even if the oil is smeared then the oleophilic epilame should pull it back to the center (see diagram below). Reference For interest the chemical in epilame is 2-(PERFLUOROHEXYL) ETHYL METHACRYLATE, CAS NO: 2144-53-8
×
×
  • Create New...