Jump to content

The better collet?

LittleWatchShop
 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

Anecdotally, I say that Levin has better collets.

I have a variety of brands.  I could be wrong but that is what I think today.

Happily, I have almost a full set of Levin collets and my bank account reflects that fact!!

nickelsilver Distinguished Member

nickelsilver

Posted
Posted

Levin makes amazing collets. But any collet can become damaged, especially smaller sizes. I have about 4 full sets of 8mm Schaublin collets, same quality as Levin, and still have to try different ones of the same size for really tricky work sometimes.

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
12 hours ago, nickelsilver said:

But any collet can become damaged

Yeah, I posted about my #11 Levin collet a couple of months ago.  Way out of round...pretty amazing.  Looking at it...it looks normal.

 

12 hours ago, nickelsilver said:

have to try different ones

I need to go through all of mine at some point and cull out the poorer ones.  A project for another day.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • nevenbekriev
      Watch runs perfect for days, and suddenly stops.

      By nevenbekriev · Posted

      Hi Joe, I mean the situation when the escapement can be unlocked when pallet fork is pressed as the guard pin to touch the guard roller. This will be possible if the guard pin is short or the depthing of the escapement is not deep enough. The pallet fork was replaced, but I don't think it was adjusted to work correctly with this movement.  Of course, if there is defect on the guard roller, it also can lead to such problem.
    • JoshuaT
      BMC crystal press die alternative

      By JoshuaT · Posted

      Hi everyone, I am new to watch repair and loving the whole process, even some of my fails…maybe. Right now I am looking at purchasing a press for fitting watch crystals, and I was wondering if any of you have had experience with the BMC model (seen in photo) and if you know whether the Robur press dies would fit, or, if not, what alternative dies might as I am having trouble sourcing original ones.   I know that the subject of crystal presses has been a well covered topic here, so I apologies for bringing it up again but I hadn’t found any past threads on this points. Any help on this would extremely helpful. Thanks! Joshua
    • steve1811uk
      First Rolex serviced

      By steve1811uk · Posted

      Hi, I just wanted to share the unmistakable quality of a Rolex made in approx. 1990. Cleaned and serviced for a friend using appropriate oils and greases, with Epilame on the parts recommended by Rolex. New mainspring and upper setting and jewel for the minute Pinion (cracked jewel). Run in overnight and then worn on the wrist for a couple of hours to warm. Without any adjustment to the balance weights the watch ran at 0 SPD DU, all positions within +3 and -2. Vertical amplitude after 24 hours of 230 degrees minimum. Watch running at zero seconds per day on wrist when worn 24 hours. Serviced just once before 20 years ago. No need to buy the Microstella regulator tool, not this time anyway 🙂 No scratches or damage caused to screw heads and bridges. All seals replaced and waterproof tested to 60 metres. All good practice for when the time comes to service my own Grand Seiko.
    • MariusJacob
      Who's doing what in the world of watches today.

      By MariusJacob · Posted

      My kid woke me up at 2:00 a.m. I couldn't get back to sleep so I decided to go to the workbench. I was to tired to work on a watch so I decided to dress up tweezers and screwdrivers while having a drink and listening to some music.     Luckily I got a comforting nap after lunch and started working on this beautiful Raketa Big Zero.  
    • tIB
      Seiko 6105 crown gasket service

      By tIB · Posted

      Good shout - I'll grab something like that and some around the required size from cousins too...
×
×
  • Create New...