Jump to content

Granddad Louis Valentin

Corstjens1

By Corstjens1
in Watch Repairs Help & Advice

 Share

Recommended Posts

Corstjens1 Member

Corstjens1

Posted
Posted

My granddad passed away, four days ago and my grandmother handed me two watches. They aren’t that good of quality but I like to wear them for a few years to remember him as da sentimental piece. When I tried to replace size the bracelet the link almost broke because it’s that poor of quality. Does anybody know what types of bracelets these are or where I could find one like this ? 

D16FBC8C-BCAB-4132-8C10-375FDC5CF967.jpeg

ADC9B29A-15A1-454D-93BC-78B17A7FFC68.jpeg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

If you have a look at cousins uk watch parts, there is a section of the catalogue which deals with bracelets, if in the US then Jules borel, Esslingers do the same. With them being quartz units check the battery housings and change the batteries.  The bracelets are tapered so measure for length and across the case lugs for the fitting width. Depending on the state of the case fitting pins, change these also.  a picture of the movements would be handy.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      I did try that last time Rich , i traced the image from the Bestfit book which is the actual size. But its more difficut to cut the shape from paper than it is to grind the steel to shape. This way is pretty easy and the final shaping is done when fitting the part. There are a couple of things i will do differently next time, clamping the 2 pieces together with a drill press will help to hold while scribing the shape in. This was a bit tricky having only one hole, if using the pins and cork the drill size needs to match the pin diameter so there is no movement at all from the template. This movement hasn't finished frying me yet, damaged thread in the plate crown wheel hole and two rubbed in cracked jewels, thats gonna be much more fun.
    • Neverenoughwatches
      A big thank you.

      By Neverenoughwatches · Posted

      👍 Whats not to follow OH ?  You're every inch a pro and a true gent, i always enjoy reading your answers even some of the clock stuff that i dont have a clue about. 
    • RichardHarris123
      Part swapper to part maker

      By RichardHarris123 · Posted

      Could you print the image either enlarged or reduced to the same size as the actual part and then glue it to the steel. 
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      Next is to drill the screwhole this then provides an anchor point so the bridge doesnt slip around while scribing the shape. A cork lid, a pin and a piece of gaffer tape ( 😅 ) keeps it all in place. The hole is measured from the broken part using a hand measuring gauge. Mark the hole, punch it and drill it off to size. The awkward bit is working out where the jumper should be and the detent positions.  I remember watching a youtuber a while back do this with dividers, so i dug out my old school compasses and improvised a little. This bridge only has one hole and to find the detent positions you need two points of reference, so i just worked the second point from one of the corners, hopefully its near enough. Then scribe in the jumper using the two detent positions ( wind and time set ) that were marked and a big picture of the complete spring to look at that helps to give you a feel of where the jumper should be.   
    • ManSkirtBrew
      Seitz Tool - Help determine if Seitz or not

      By ManSkirtBrew · Posted

      Right now I'm making do with a similar micrometer (the one below is $45 shipped but you can find better deals) and a $20 stand. You do have to be excruciatingly careful measuring jewels, since there's no table, but if you don't have the $500 to throw around, it's a nice option.
×
×
  • Create New...