Jump to content

Seiko 7009: Conversion Mechanical → Quartz ; Help!!

boblalux

By boblalux
in Watch Repairs Help & Advice

 Share

Recommended Posts

boblalux Watch Enthusiast

boblalux

Posted
  • Author
Posted

ricardopalamino/

 

Just a very final mail;  when I tried to register/log in to the site TheWatchSite forum I get the following message....

"You have been banned for the following reason:

No reason was specified.  

Date the ban will be lifted: Never"

 

Can't understand it !!!     So I can't go to the Seiko/Citizen sub-forum.

Bob

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Hi Bob....from the other Bob,

 

I agree with BL and all the other members' comments/advise. Dial feet are attached with double-sided tape also available for this purpose. Also the VX43 movement requires watch hands: hour 1.10, minute .65, and sweep second .20 mm. The dial feet holes are @1 and @7 ish so they might not align with the original dial and reposition of feet might be required. The overall high of the movement is 4.5 mm but the actual high is 2.92 mm. Question: how do those measurements compare with the original movement (the old one)? This could be a problem...

 

Cheers,

 

Bob

Link to comment
Share on other sites
boblalux Watch Enthusiast

boblalux

Posted
  • Author
Posted (edited)

Thanks, Bob.

I think I will be able to adapt for any difference in the hand hole diameters.  But one problem:  I'm having difficulties trying to remove the old Seiko stem 354 022 Tap 10 from the crown.  I need the crown for the new stem 351 177.  It hasn't broken YET.  I tried with WD44 and also boiling water to soften any glue, but it still won't unscrew.  How can I find the part number for the 7009-3140 crown before I break its stem?

 

To your points:  the dial has no feet and I will be able to place the feet anywhere on the dial, after carefully centring the dial an taking regard for the stem at 4 o'clock.

 

 

Bob

Edited by boblalux
Link to comment
Share on other sites
boblalux Watch Enthusiast

boblalux

Posted
  • Author
Posted (edited)

Blacklab:   Thanks for the tip, I'll try and remove the o-ring and acetone the lot (assuming its glue, and not overtightening or rust) !  Where on earth did you find the part no.?  I tried everywhere, and it won't 'Google'!

Bob

Edited by boblalux
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Hi Bob,

 

Boley has an extensive catalogue of parts by case serial number. Also, what I do after heat, and rust treatment stubborn, rusted crown/stem, I do a quick, light tightening of the crown and immediately unscrew it from the stem. Most of the time it works. Make sure your pin vise is well tightened and on the right spot on the stem (usually not on the thread but immediately after, on the thicker smooth stem but before the machined part).

 

Hope it works,

 

Cheers,

 

Bob

Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

ricardopalamino/

 

Just a very final mail;  when I tried to register/log in to the site TheWatchSite forum I get the following message....

"You have been banned for the following reason:

No reason was specified.  

Date the ban will be lifted: Never"

 

Can't understand it !!!     So I can't go to the Seiko/Citizen sub-forum.

Bob

 

I am sure that there is an error in registering somehow . Google Seikocitizenwatchforum and you will see a registration link . If the problem persists LMK and I will ask one of the moderators if there is a problem . If you do register also LMK . It is a great site for Seiko and Citizen watches with lots of tech references .

Link to comment
Share on other sites
boblalux Watch Enthusiast

boblalux

Posted
  • Author
Posted

<<Boley has an extensive catalogue of parts by case serial number. Also, what I do after heat, and rust treatment stubborn, rusted crown/stem, I do a quick, light tightening of the crown and immediately unscrew it from the stem. Most of the time it works. Make sure your pin vise is well tightened and on the right spot on the stem (usually not on the thread but immediately after, on the thicker smooth stem but before the machined part).

 

Hope it works,

Cheers,

Bob>>

 

Worked a dream, many thanks.  After removing the rubber neck gasket, I 'acetoned' it overnight, chucked it in boiling water for a minute, then - off it screwed with no damage!

By the way, my last attempt resulted in a stem broken off flush with the crown!!  I read about the 1 week's vinegar treatment with scepticism, but it worked!!!      

Thanks for the Boley's tip: Unfortunately, they only sell to the trade.

Bob

Link to comment
Share on other sites
boblalux Watch Enthusiast

boblalux

Posted
  • Author
Posted (edited)

I am sure that there is an error in registering somehow . Google Seikocitizenwatchforum and you will see a registration link . If the problem persists LMK and I will ask one of the moderators if there is a problem . If you do register also LMK . It is a great site for Seiko and Citizen watches with lots of tech references .

I tried again, same problem.  Twice I wrote to the Webmaster - no reply.  Just don't understand it.

When I think back about a year ago, I had an altercation with a seemingly arrogant moderator somewhere on the 'net (so it is possibly here).  Perhaps that's why.  But not giving a reason beats me!

Edited by boblalux
Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

Atta Boy...Perseverance will win the day .

 

" I had an altercation with a seemingly arrogant moderator somewhere on the 'net (so it is possibly here).  Perhaps that's why.  But not giving a reason beats me!"

 

I have a hunch just who that might be..... so your description fits ....... I call them "the Politicians "...but no matter , 99.99%  of the rest of the members are here for the joy of Horology .

Link to comment
Share on other sites
Blacklab Distinguished Member

Blacklab

Posted
Posted

Blacklab:   Thanks for the tip, I'll try and remove the o-ring and acetone the lot (assuming its glue, and not overtightening or rust) !  Where on earth did you find the part no.?  I tried everywhere, and it won't 'Google'!

Bob

Here: https://www.cousinsuk.com/category/seiko-case-parts just type in the full number - 7009-3140 lookup select & then search for items or here: http://cgi.julesborel.com follow the instructions & it takes you here: http://cgi.julesborel.com/cgi-bin/matcgi2?ref=sek+cs%237009-3140&submit=Search

  • Like 1
Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

Here: https://www.cousinsuk.com/category/seiko-case-parts just type in the full number - 7009-3140 lookup select & then search for items or here: http://cgi.julesborel.com follow the instructions & it takes you here: http://cgi.julesborel.com/cgi-bin/matcgi2?ref=sek+cs%237009-3140&submit=Search

 

 

Boley has a similar feature , Under case parts type in your numbers and ....Voila....magic .  And of course , don't forget Ranfft , ....a plethora of information .

 

 

 

 

post-808-0-23621200-1427743110_thumb.png

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      Mainspring winder question.

      By VWatchie · Posted

      Excellent advice!  Mainspring winders are generally a nightmare. In order to be absolutely sure that they work, they must be adapted for specific calibres. Sure, you can build up a collection of winders over time, but it's expensive and time-consuming and you still can't be sure that any of the ones you have in your collection will fit. When I was new, I considered buying Bergeon's large universal set because I thought it would cover all situations, but that's not the case. The risks of hand winding a mainspring are often exaggerated. With the right technique and training, the risks are not much greater than with a winder. Moreover, if the spring has a T-shaped bridle, you may not even get it into the barrel. Here is an excellent description by a professional how to hand wind: Yes, a well-established practice among professional repairers is to always replace the spring even when it is in good condition. Personally, I think it is an unnecessary cost because modern springs last a very long time. Some fatigue occurs over time but if you are unsure, you can always test the power reserve. It is also an unnecessary risk to replace a spring if it is still in good condition. If an original spring is not available, it is not certain that the alloy in a generic spring corresponds to the properties of the original spring. This seems to be particularly true for some Japanese movements, especially Seiko and Orient. For any Swiss movement, I'd say the risk is non-existent.
    • rjenkinsgb
      Mainspring winder question.

      By rjenkinsgb · Posted

      I had a similar problem with a chinese set - with that, I drilled the drum out to take the slightly larger arbor; it only needed about 0.2mm increase so no detriment when using the original arbor. (One was LH the other was RH, in that case).
    • Neverenoughwatches
      Wheel pivot

      By Neverenoughwatches · Posted

      There is a tool to straighten this, but it will cost you 50x this wheel.
    • Neverenoughwatches
      Dial Dots

      By Neverenoughwatches · Posted

      The devil's creation. They peeled off very easily, yeah no not recommended. 
    • Waggy
      Wheel pivot

      By Waggy · Posted

      You have a very low chance of straightening this, it should be made of hardened steel, which is very brittle. Maybe you could ask for a refund from the place where you bought it? If you go ahead and try to straighten it and it breaks then nobody will refund you.
×
×
  • Create New...