Jump to content

Last Question I Promise

bjd1020

By bjd1020
in Watch Repairs Help & Advice

 Share

Recommended Posts

bjd1020 WRT Addict

bjd1020

Posted
Posted

So onto my 7750 venture and its taken me 6 months but I am there......well almost. One thing I just havent been able to get confident with is the balance work, IE hairspring, regulator, etc etc. I have tried and practiced and destroyed. Lol. Its expensive training.....lol. Anyway I think when it comes to the balance assembly id prefer to leave that to an expert. I have these parts and am looking for someone to put them together for me. Id be willing to trade a favors if at all possible. I honestly dont expect free service but im also not going to pay rolex shop prices. Anybody interested let me know.....or if you think you can coach me through it. This work just seems like its on another level all together. d64e8150c4f9e62f56f95b619cf4e4f0.jpga5c4e4d3e41e59bed2eebbea67f76f9c.jpg

 

Sent from my SM-G950U using Tapatalk

 

 

Link to comment
Share on other sites
jnash Super WRT Addict

jnash

Posted
Posted

I would put your 7750 aside and take some cheaper o watches and practice in them first, balances can be tricky, however only way to learn is to practice. Was a few years before I started on 7750s

  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

I agree with jnash, putting this project aside, tricky regualtor pin and stud installation.There was talk of some video on the forum showing how to install the pin and stud Best to invest time reading on and practice before you attempt.

I once damaged the regulator arm when trying to install the pin. 

Link to comment
Share on other sites
bjd1020 WRT Addict

bjd1020

Posted
  • Author
Posted

Ive had a lot of folks give me that exact same advice.....although my wallet wouldnt agree but im glad I didnt listen. The 7750 was the movement I began on, I quickly picked up the elgin 462, and then subsequently the venus 170 when I learned of the castle wheel mechanism. So essentially I have 3 builds going on at the same time where I have been hopping back and forth. I ran into this same problem with the balance assemblies on the 170 and a guy who has a shop TX built them for me. I may reach out to him. I have some ideas on building some specific tooling to assist in putting these together. This may sound crazy but it seems as though the issue is for me of a physical nature. I just dont think I am steady enough to do the work. Anyway if you happen to have the link to that video send it over. Ive watched plenty and its not a matter of understanding.

Sent from my SM-G950U using Tapatalk

Link to comment
Share on other sites
bjd1020 WRT Addict

bjd1020

Posted
  • Author
Posted
Hi, So far as I know the forum places no limits on the number of questions one can ask.  Personally I enjoy talking watch repair to you.really :geek:
Lol. It is a fascinating subject for sure. I completed my second 7750 movement resoration last night. This time it was perfect on the machine with no adjusting. Im also getting faster and faster at putting this thing together. I did end up sending out the balance work. I will tackle it, just not yet. ecc7b452dab552b200de1cb32b110b04.jpg

Sent from my SM-G950U using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • AlanB
      Gilding after silver soldering

      By AlanB · Posted

      When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • Neverenoughwatches
      Can anyone identify what this is? Part Two

      By Neverenoughwatches · Posted

      The first one is an Unruh max stake for pushing out staffs
    • JonC
      Can anyone identify what this is? Part Two

      By JonC · Posted

      Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • Zedster
      Roamer Searock Crystal problem

      By Zedster · Posted

      According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
    • JonC
      Dial feet removal

      By JonC · Posted

      When building a new Watch I have tended to use a file to remove the remnants of dial feet that are not needed as many dials come with four feet to accomodate different movements, but this can be a bit messy so now I use this with a great deal more precision as you can use an appropriate bit for the job and keep it very localised.      
×
×
  • Create New...