Jump to content

Missing pendulum

dnhb

By dnhb
in All Things Clocks

 Share

Recommended Posts

dnhb WRT Addict

dnhb

Posted
Posted

A friend has inherited a mantle clock (Westminster Chime) which is missing its pendulum. I'd be grateful for advice as to what nature (weight, size etc) of pendulum I should be looking for.....

20240919_133510.jpg

02cxnbkw.png

oldhippy Distinguished Member

oldhippy

Posted
Posted

The easy way is to fix some weight  2 to 3 oz where the pendulum hangs set it to time and see how it goes for a few hours, if you see a significant change in time in the two hours adjust weight accordingly. You need to make sure it has a nice even tick tock.  

  • Like 1
dnhb WRT Addict

dnhb

Posted
  • Author
Posted
4 hours ago, oldhippy said:

The easy way is to fix some weight  2 to 3 oz where the pendulum hangs set it to time and see how it goes for a few hours, if you see a significant change in time in the two hours adjust weight accordingly. You need to make sure it has a nice even tick tock.  

Thank you. Could you please tell me the proper term for the type of connection the pendulum rod needs to have given the form of the suspension bar shown in the picture?

oldhippy Distinguished Member

oldhippy

Posted
Posted

The part is called a leader which the pendulum hangs on. The top of the leader hooks onto the suspenspring, the s/s needs to be good, not bent or crooked but straight. 

Sorry for the delay I had my sister over yesterday. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Simeon
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By Simeon · Posted

      Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • caseback
      Chinese tools debate

      By caseback · Posted

      He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
    • Malocchio
      Chinese tools debate

      By Malocchio · Posted

      Seems like he doesn't have the micrometer cap  attached to the spindle so he can only push down but cannot pull up? If the cap screws into the spindle I guess you don't need the spring? I only have a "normal" Seitz so I really have no idea. 
    • Edwinsh21
      Christopher Ward SH21 Winding Rotor Bearing replacement

      By Edwinsh21 · Posted

      Do you have a part number for the bearing shim lock tool?
    • Dell
      Lathe motor advice

      By Dell · Posted

      Yes in my opinion the 3/4HP is plenty but it’s your decision & yes it does come with speed control but foot operation so my reason for changing to potentiometer was because my leg shakes so it was like me revving the lathe & anyway I prefer to set the speed. I & a few others that I recommended the motor to run a Pultra 10mm lathe so if you have a 6 or 8mm B & L then it will be plenty, if you have seen any of my videos you will have seen that when using a graver I run quite slow without any problems. Dell
×
×
  • Create New...