Jump to content

misaligned Day/Date on Victorinox swiss army automatic watch

erdos
 Share

Recommended Posts

erdos New Member

erdos

Posted
Posted

Greetings!  

My first post here and hope i'm posting at the right place for seeking help.

I have Victorinox Swiss Army automatic watch, was given to me as a gift about a month ago.  it ran fine for several weeks, but then its day/date calendar on 12 and 6 o'clock positions began to become misaligned.  The day indicator stops between two adjacent days and date looks to be not centered as well.  

I believe it's called Ambassador series (model number 249072), and comes with ETA 2834-2 movement,

Not sure what might have caused this, I didn't accidently drop it or knock it on some hard surface,  is this fixable without resorting to a professional repair service?  

one picture shows when i first got it, the other shows its current state

Nucejoe Distinguished Member

Nucejoe

Posted
Posted (edited)

Can be due to friction  or wear in day/date mech. 

Would it change right ( eventually) or  when hr/min hands are advanced through the crown manually ? 

A clean & lube might/ might not fix it, if didn't , spotting the fault is work of experienced hands. 

Rgds

 

 

 

Edited by Nucejoe
  • 1 month later...
CYCLOPS WRT Addict

CYCLOPS

Posted
Posted

might try to manually adjust the day and date in the second stem position-might free something up, don't do it between 6pm and 12pm to be safe, if doesn't help Nucejoe might have the right idea...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Birbdad
      Regulating is too touchy

      By Birbdad · Posted

      So if anybody overrides what i say, listen to them haha. I'm not an expert but i've just been in this boat a dozen times as i used to mess up hairsprings bad, but the good part of that was that i got to learn how to fix them.  What made my life SO much easier was learning how to adjust the hairsprings with the balance installed on a disassembled mainplate, unless it's a very serious problem or on an inner coil you can't get to i would recommend trying this in part because the spring will mostly ALWAYS look flat when the balance wheel is not installed on the cock. Install the balance wheel back in the cock and the cock with the cap jewels in the mainplate, with it installed even the most imperceptible twist will be pretty obvious. Just make sure the balance jewels are also installed. In these movements, if 99% of the time any twist or problems gonna be around the terminal curve, twists often near the stud, especially if you've been removing their awfully designed studs from the balance cock. If there's a reliable way to install those things without introducing a minor twist to them i haven't found it. they're an awful design. INstall the balance on you mainplate WITH your capstones/chatones and look sideways across the balance under magnification. Look for the highest or lowest spot of the now not flat hairspring. 180 degrees from that high or low spot is where your twist will be. You have to be VERY careful with twists as the tiniest over or under twist brings it out of flat. If the area i have to untwist is near the stud i just use a pair of #5 tweezers or some very sharp fine curved tweezers and gently see which way i twist it corrects the twist, then i hold the very fine point of the tweezers on the hairspring and just gently squeeze and check it and see if it started to correct it, then i rinse and repeat. Tiny adjustments is what you want, don't close them all the way, and dont' introduce a flat spot in them. it's just a little nudge by closing the tweezers on it at an angle. .  If the twist is not near the stud, i grasp the hairspring with some very fine curved tweezers as gently as possible while still holding it then i do that same sorta tweezer squeeze with my #5's. 
    • AndyGSi
      Omega Cosmic 2000 split stem question

      By AndyGSi · Posted

      Has it got the logo on the crown. I think you're best option is going to be to remove the damaged stem and measure it. Edit Do you have the case reference number.
    • Shadaar
      Omega Cosmic 2000 split stem question

      By Shadaar · Posted

      Movement is Omega 1012. I bought this from Cousins: 
    • Nucejoe
      Hello from Denmark

      By Nucejoe · Posted

      Welcome to the WRT forum.
    • Embezelled
      Where it begins

      By Embezelled · Posted

      To get the full diameter, I'd have to take it out of the case, which I won't be able to do until the screwdrivers arrive.  I doubt that it's much use to you, but the raised rim on the case, encircling what you see of the movement, has an outer diamter of 28 mm and an inner diameter of 24.8 mm. The case outer diameter is 32 mm.
×
×
  • Create New...