Jump to content

GSTP, nervous repair

kevlarpants
 Share

Recommended Posts

kevlarpants Member

kevlarpants

Posted
Posted

Hi, I have just purchased two GSTP watches which don't run but look like a great challenge now I've done a couple. Mainly for the history, it would be great to bring these back to life. 

However, I then realised there may be an issue with the lume used in those days and don't fancy working on them in full haz suit!.

I don't want to invest in a geiger counter either but can't stand the thought of not trying. 

I appreciate you can't tell me to go ahead but any advise would be appreciated. 882856967_s-l1600(4).thumb.jpg.8f72f1b32f60426433fc40b00a633e0e.jpg1018526292_s-l1600(3).thumb.jpg.9d6bf2188d2f75629ab6edf1e6ab4be2.jpg

 

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted (edited)

You don't need to worry.  The Kevlar will protect you!!

I thought this topic had already been fleshed out on WRT, but I searched "radium" and did not find the thread.

Bottom line...you need not worry...not for a moment.  Do not lick the dial, nor the hands.  I suspect that even if you did, it would have zero impact.  I have several reports commissioned by the US government that provides an analysis of a variety of scenarios (professional watchmaker, amateur watchmaker, wearing in chest pocket, on the wrist, etc.).  It is just not an issue.  Moreover, my anecdotal evidence is that my father was a watchmaker working on watches from 1946 until 1990.  I know he had and worked on many radium watches.  He died at 93 of causes unrelated to radiation.

Go read this thread.  The documents I mentioned can be found there.

Edited by LittleWatchShop
  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Simeon
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By Simeon · Posted

      Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • caseback
      Chinese tools debate

      By caseback · Posted

      He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
    • Malocchio
      Chinese tools debate

      By Malocchio · Posted

      Seems like he doesn't have the micrometer cap  attached to the spindle so he can only push down but cannot pull up? If the cap screws into the spindle I guess you don't need the spring? I only have a "normal" Seitz so I really have no idea. 
    • Edwinsh21
      Christopher Ward SH21 Winding Rotor Bearing replacement

      By Edwinsh21 · Posted

      Do you have a part number for the bearing shim lock tool?
    • Dell
      Lathe motor advice

      By Dell · Posted

      Yes in my opinion the 3/4HP is plenty but it’s your decision & yes it does come with speed control but foot operation so my reason for changing to potentiometer was because my leg shakes so it was like me revving the lathe & anyway I prefer to set the speed. I & a few others that I recommended the motor to run a Pultra 10mm lathe so if you have a 6 or 8mm B & L then it will be plenty, if you have seen any of my videos you will have seen that when using a graver I run quite slow without any problems. Dell
×
×
  • Create New...