Jump to content

seized screw .... help

LeCorbusier
 Share

Recommended Posts

Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
1 hour ago, LeCorbusier said:

Yes I have a staking set ... The setting lever looks very similar ... but it doesn't have the spring at all.

I will see if I can extract dims from the staff and take it from there I think ... if it doesn't match I can always search for one that does I suppose.

This is the main reason i will be learning to repivot a staff. Much practise will be needed i am sure. At 55 I'm expecting to have the skill and technique down by full retirement age. My eyesight will then be too crap to use that skill 🙄 

Link to comment
Share on other sites
LeCorbusier WRT Addict

LeCorbusier

Posted
  • Author
Posted

it will certainly be an interesting challenge ... no idea how things will go ... but currently its broken so apart from trashing the new staff (assuming I can track down an appropriate one) I can't really make matters worse. Re-studding the hair spring and fabricating the wedge pin was a similar challenge and one which I would rather not do very often.

 

Link to comment
Share on other sites
  • 3 months later...
LeCorbusier WRT Addict

LeCorbusier

Posted
  • Author
Posted

I am coming back to this after putting away for a while to take stock. I am still trying to work out how to get the dims of the right balance staff with the pivots broken. My current plan is to remove the cap jewel from the cock and take a measurement from the cock to the face side of the plate and then subtract the thickness of the plate cap jewel. That should in theory give an accurate dim  from face of jewel to face of jewel ... am concerned that it doesn't allow for end shake tho. any thoughts or advice on this would be appreciated. I was then going to see what was catalogued at Balancestaffs.com and see if there is a match for an AS staff and what ligne that would compare to?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      Accutron 218 transistors

      By ManSkirtBrew · Posted

      Update: I posted over on NAWCC and it looks like I melted the fine coil wires where they come into the solder lugs. After dropping the heat way down on my iron and being absurdly careful, I have a humming fork!
    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
×
×
  • Create New...