Jump to content

Victorinox Stem Replacement Help

Papagun

By Papagun
in Watch Repairs Help & Advice

 Share

Recommended Posts

Papagun New Member

Papagun

Posted
Posted

Aloha,

 

I am brand new here and have never repaired a watch before. Years ago I purchased a Victorinox watch and before I even wore it, the sweep hand fell off. I threw it in a drawer and forgot about it. A week or so ago, I decided to try and reattach the sweep hand as well as replace the battery. In order to remove the movement to access the sweep hand, I had to remove the winding stem which I managed to do somehow. I did unscrew the small plate that appeared to hold the stem in place. In any event, I do not know how to replace the stem. I inserted it ito the movement and reattached the plate but the stem simply falls out and does not engage the gears to adjust the time.

Any help out there?

Mahalo,

Papagun  - Wahiawa, Hawai'i

IMG_1028.JPG

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ColinC
      Standard crystals to replace tension ring crystals

      By ColinC · Posted

      When can you use a standard crystal to replace one that had a tension ring? The first time I popped a crystal with a tension ring out of a watch I found that I had a suitable sized standard crystal and decided to try that.  It fit nicely and it was hard to see that anything was missing from the watch.  I understand that it probably reduced the water resistance of the watch but since it was an old dress watch it wasn't going for a swim anyway! I have since tried the same thing on another watch and found that the tension ring seemed to have an additional role of holding the dial in place.  With the standard crystal in there the dial and movement falls forward. This means it rattles in the case and falls forward and the hands fowl on the crystal (when the dial is down). Is there a trick I am missing here or does this watch require a special crystal?  I am reluctant to buy an expensive armoured crystal only to find I have the same problem.  
    • Levine98
      Chinese clone demagnetizers

      By Levine98 · Posted

      So I wrapped the anvil it in bubble wrap and passed ot through the demag only. Still no go—the unit is simply too strong.  next experiment is to use a VARIAC to lower the voltage and see if that reduces the magnetic field. 
    • VWatchie
      Need some crystal replacement advice

      By VWatchie · Posted

      In this case, the underside of the crystal is flat so I assume I don't have to worry about clearance to the hands. However, perhaps I'm missing something. If so, please let me know. I guess no one has the patience to get into the details of my first post so here's a simplified version of my question: The case diameter for the glass gasket is 36.9mm. However, Cousins doesn't have a glass gasket with that diameter. The closest are 36.8mm and 37.0mm. Would any of those two options work, and if so which one? I have no problem ordering both and testing them, but If someone already knows it is pointless, there's no reason to order. No, I haven't. Is there someone you can recommend? Preferably in Europe. Thanks!
    • rjenkinsgb
      Dangerous substances when disassembling timex indigloo?

      By rjenkinsgb · Posted

      No. It's incredibly volatile and evaporates in seconds; there is no way it would last as long as it took to just install the part cleaned in it, in the movement.  
    • ColinC
      404 Club Reboot

      By ColinC · Posted

      When I record how much I have spent on each watch I include the postage.  UK EBayers seem to be charging £5 minimum these days on postage.  Have made a couple of job lot buys recently - based on the average price this one could be 404 reboot project  Bad photo from eBay - 1 of 4 watches for a total of £21.19. A Medina with an MST 385 movement - Soaked in oil but looks like it will run again!
×
×
  • Create New...