Jump to content

Rodania Quartz Movement - Batteries

mcoulton
 Share

Recommended Posts

mcoulton Watch Enthusiast

mcoulton

Posted
Posted

Hello

I'm servicing a Rodania Quartz and I'm unable to figure out the type of batteries required to get it to work again. I can't locate any numbers on the movement and a search of the internet via Google or ChatGPT hasn't produced any results. If I post some pictures of the movement & watch would someone be kind enough to advise me of the type of batteries I need to buy? The batteries would need to be thicker than I'm use to as the depth of the battery pocket is larger than I've seen before. Thanks in advance for any help that can be provided. 

1.jpg

2.jpg

3.jpg

4.jpg

5.jpg

AndyGSi Distinguished Member

AndyGSi

Posted
Posted (edited)

I'd expect them to be an SR41, SR43 or SR44 but if you measure the diameter you'll be able to see what's required from the list below.

Edit

This just shows the Low Drain SW Versions but you may be better going for the High Drain W Version.

image.png.1e959447e56ada1ab1763d8caec00c27.png

Edited by AndyGSi
mcoulton Watch Enthusiast

mcoulton

Posted
  • Author
Posted

Thanks for the help. Using my digital caliper I was able to determine that I need to order two SR41SW / 373 batteries. Where did you find this chart as there maybe one for a high drain battery?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Simeon
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By Simeon · Posted

      Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • caseback
      Chinese tools debate

      By caseback · Posted

      He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
    • Malocchio
      Chinese tools debate

      By Malocchio · Posted

      Seems like he doesn't have the micrometer cap  attached to the spindle so he can only push down but cannot pull up? If the cap screws into the spindle I guess you don't need the spring? I only have a "normal" Seitz so I really have no idea. 
    • Edwinsh21
      Christopher Ward SH21 Winding Rotor Bearing replacement

      By Edwinsh21 · Posted

      Do you have a part number for the bearing shim lock tool?
    • Dell
      Lathe motor advice

      By Dell · Posted

      Yes in my opinion the 3/4HP is plenty but it’s your decision & yes it does come with speed control but foot operation so my reason for changing to potentiometer was because my leg shakes so it was like me revving the lathe & anyway I prefer to set the speed. I & a few others that I recommended the motor to run a Pultra 10mm lathe so if you have a 6 or 8mm B & L then it will be plenty, if you have seen any of my videos you will have seen that when using a graver I run quite slow without any problems. Dell
×
×
  • Create New...