Jump to content

Stripping gold plate/replating

pent

By pent
in Polishing & Refinishing

 Share

Recommended Posts

pent Watch Enthusiast

pent

Posted
Posted

So, I'm ready to try my hand at some gold plating.  I have a few old, non-valuable pocket watch cases that are base metal with gold plating (and judging from what I've done so far, QUITE a thin layer of plate).  I've taken a few passes with a cotton wheel and Dialux grey.  It certainly looks like crap now, but I'm not sure if I'm down to the base metal yet.  I'm considering Dialux yellow or orange for the cutting power to get more plate off, but I don't want to overdue it and remove the design/graving.  

Just wondering if anyone has intentionally (or accidentally) taken the plating off down to to the base metal.  What did you use or how did you do it in a time-efficient manner without dulling the designs.  Pics of where I'm at so far below.  I included an untouched case and the back of the case for color comparison.IMG_1330.thumb.JPG.589f5c2976cdaaffe69e7fca9f66a170.JPGIMG_1331.thumb.JPG.1cee6e5097d63e24b5a7c4a41b1b49cd.JPGIMG_1332.thumb.JPG.9233599d5dd4d711f72e4e38e0a00a64.JPG

Link to comment
Share on other sites
  • 2 months later...
mikepilk Distinguished Member

mikepilk

Posted
Posted

I have a wristwatch case I want to reverse electroplate. The gold plating is flaking off. Under it is either rose gold or copper, and below that, I assume, nickel over the brass case.

It's a mess, so I want to remove all the gold, and replate with nickel (I thought I'd like to try gold plating until I saw the price of the solution).

Is there an easy way to remove the gold plate without a gold solution ?

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
3 hours ago, mikepilk said:

I have a wristwatch case I want to reverse electroplate. The gold plating is flaking off. Under it is either rose gold or copper, and below that, I assume, nickel over the brass case.

It's a mess, so I want to remove all the gold, and replate with nickel (I thought I'd like to try gold plating until I saw the price of the solution).

Is there an easy way to remove the gold plate without a gold solution ?

A similar question i asked a few days ago but not in relation to gold.  Ordered today sodium bisulphate salt to make up the pickle and hoping will be strong enough to strip plating and for use as a screw remover.The copper layer you are seeing might be a copper strike. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Pallet jewel

      By Neverenoughwatches · Posted

      The entry and exit stones have different impulse face angles  murks.
    • Waggy
      First Project Already A Bit "Sideways"

      By Waggy · Posted

      Depending on how much of the screw is left, you may be able to screw it further in and it may fall out of the hole that the dial foot sat in. To do this I rough up the tip of the good screw and screw it in, often the rough surface of the good screw and the rough surface on the broken screw get enough of a bite to transmit the torque into the broken section and force it out the other side. Like I said the size of the broken screw needs to be in your favor, but you never know you may get lucky.... or if you get it moving you may be able to then back it out with a screwdriver taking a bite on the rough surface. worth a try
    • DDean
      First Project Already A Bit "Sideways"

      By DDean · Posted

      I will try this weekend.  I've tried several times with my cell phone and it's just too small and recessed to get a good picture.  I need to get my macro lens and tripod out and then figure out how to get enough light down the hole in the side of the man plate to  actually show the top of the broken screw. I appreciate the effort and will try and get that pic this weekend.
    • RichardHarris123
      Simeon from Down Under

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Simeon
      Simeon from Down Under

      By Simeon · Posted

      Hi,   My name is Simeon I am based in Sydney, Australia and have recently got into watch repair / watch making.  I am very much a learner having serviced multiple forgotten watches, some of which were actually successful!   I have a slowly growing collection of watches, mainly old Soviet, a few Japanese and (not pictured) some Raketas, a Poljot Alarm, an Omega Speedmaster Reduced and a vintage (1972) Tissot Seastar.  I like unloved vintage watches, with quirky faces and enjoy bringing them back to life through the simple(!) act of disassembly, clearing and reassembly. I am an Electrical Engineer who also undertook a trade apprenticeship so I am reasonably handy - It's fair to say, I know just enough to get myself in trouble. 
×
×
  • Create New...