Jump to content

Ladies Seiko 4206-0519 A4 needs crystal

Davis
 Share

Recommended Posts

Davis Watch Enthusiast

Davis

Posted
Posted

Looking for a crystal for my Seiko find. Rear case showns 4206-0519 A4. Dial shows 4206-258x-R1. 

I am not sure if the crystal just pushes out from behind or I have to remove the bezel first. Saw somewhere I think for a waterproof case,that you push on the ridge on the inner ring rather than the crystal. Never worked on this type of assembly before. Reviewed the Seiko case service manual but it did not look a type R crystal.

Tried all the searches and the Ofri site to no avail.

Any comments would be appreciated. Dave

 

IMG_4985.jpg

IMG_4986.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • tIB
      Seiko 6105 crown gasket service

      By tIB · Posted

      Thanks for the info - I'll go big on the gaskets... Wonder if anyone sells hundred packs?!
    • steve1811uk
      Rolex 3135 rate variation with temperature

      By steve1811uk · Posted

      Looked into this some more and I believe that some of the increase in rate is attributable to the drop in amplitude after 12 hours off wrist, from 300 to 275 degrees horizontal and some is due to the lower temperature (38 to 18 degrees). I can see that approx 3 to 4 seconds a day is attributable to each. I can be happy with that.
    • Nucejoe
      Removing the hairspring from a ETA 2846 balance

      By Nucejoe · Posted

      Link below shows the tool used to push the stud out. You can make the tool , just file a screwdriver to this shape.  https://www.esslinger.com/bergeon-16918-etachron-stud-remover-screwdriver/ There are vids on YouTube showing how the stud is to be  push out. Shouldn't get over creative, just go by this approach.  Good luck.
    • Embezelled
      Almost ready

      By Embezelled · Posted

      Hi all, I'm almost ready to make my first attempt at watch repair. My initial goals are very modest, just to get an inexpensive watch or two to work on, and take it at my own pace. I have what I think are the necessary tools on the way. A couple of things arrived already: a loupe, some tweezers, and a cheap demagnetizer. After looking at the options for oils and grease, I decided to start off with Citizen A-O2 and A-O3 oil, and Seiko S-3 grease. The Moebius was just too pricey to buy this early into the undertaking, when added to the cost of the other tools I've bought. Screwdrivers are Kwong Yuen for now, but I took the frequent advice on tweezers and bought Dumostar 3C and will probably add more DuMont later. I'm looking forward to making a start. I'll need a watch to work on, so I'm trying to line up an auction purchase within the next week. I've been mostly looking at Seiko and Citizen, and will perhaps a Seiko Crown if I can land one at a decent price. 
    • GPrideaux
      Seiko 6105 crown gasket service

      By GPrideaux · Posted

      I tried pushing to dome the washer in and had no success, but stuffing it full of o-ring gaskets worked much better than I expected. It takes some pressure but not as much as you might imagine, but it does take patience ... and a couple of dozen small gaskets. I used the pendant tube of a watch case to stuff the gaskets in as I didn't have a way to machine a tool to suit.
×
×
  • Create New...