Jump to content

Smiths Streamline


Recommended Posts

Not strictly a walk through but just a few notes & pics on my latest rebuild, this being a Smiths Streamline, C60 calibre with date from 1966.

 

As received non running minus the knackered strap & badly scratched crystal:

post-80-0-06951000-1448313487_thumb.jpg

Note the the damage to the lugs, probably caused by a poorly fitting metal strap some time in its life. Just something we will have to live with.

 

Out of the case:

post-80-0-23037500-1448313489.jpg

 

Under the dial:

post-80-0-89569100-1448313491_thumb.jpg

post-80-0-66879200-1448313494_thumb.jpg

 

& turn it over:

post-80-0-04580900-1448313497_thumb.jpg

post-80-0-69086700-1448313499_thumb.jpg

 

The mucky mainspring:

post-80-0-30777200-1448313501.jpg

 

Cleaning, oiling & re-assembly was fairly straightforward although the pivots proved a bit of a pain to line up and the cap jewels were not the easiest, but all went well in the end. The dial was in particularly good nick, after the Rodico + spit & cotton bud treatment. With a new strap and crystal this is what we get:

post-80-0-94505600-1448313484_thumb.jpg

Keeping time within +/- 5 seconds a day, a low 206 degrees amplitude (original mainspring) & amazingly no beat error.

 

Probably the best movement to come out of Smiths Anglo Celtic Factory at Ystradgynlais (the quality stuff being built at Cheltenham), quite sophisticated in design & general build quality, unfortunately let down by a lack of jewels, but in their defence they were trying to produce an Everyman watch at a reasonable price.

  • Like 4
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
    • When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • The first one is an Unruh max stake for pushing out staffs
    • Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
×
×
  • Create New...